Programming - krispol STARCUS series Montageanleitung

7. Programming

1 Preparation
2 The lever releasing the carriage is set in the horizontal position, move the door manually
3 Turn on the power, the lamp lights up when the display shows a value from '99' to '11'
4 The display shows the standby position '- -'
Setting the opening and closing position
5
6 Press and hold the "P" button, until 'P1' is displayed
7 Press the "P' button again, 'OP' will be displayed
8 Press and hold down the "∆" button, during opening process 'OP' flashes
9 Release the "∆" button when the opened position is reached
10 Use "∆" and " " buttons to adjust the opening position
11 Press 'P", 'CL' will be displayed
12 Press and hold down the " " button, during opening process 'CL' flashes
13 Use "∆" and " " buttons to adjust the closing position
14 Press "P", the door will open and close automatically to establish the required normal mechanical force. '- -' will be displayed at the end
15 Adding remote controls.
16 Please press the "C" button, 'Su' will be displayed.
17 Select and press the button on the remote control.
18 Press the same button again to confirm. 'SU' will start flashing, and then you will see '- -'.
Repeat the above steps to add additional eKey remote controls. The memory may store the maximum of 20 remote controls. An attempt to
19
add another remote control will result in displaying 'FU'
20 Deleting remote controls
21 Note: This feature will delete all remote controls
22 Press and hold the "C" button for 8 seconds. 'dL' will be displayed.
23 Adjusting the mechanical force
24 Press and hold the "P" button, until 'P1' is displayed
25 Press the "∆" button once. 'P2' will be displayed
Press "P" again. The current force settings will be displayed. Simultaneously, press "∆" or " " to increase or decrease the force value by one
26
step. The maximum value is 'F9', while the minimum is 'F1'. Press P to confirm.
27 The default settings is 'F3'
28 Photocell activation and deactivation
29 Press and hold the P button until 'P1' is displayed
30 Press the "∆" button twice. 'P3' will be displayed
31 Press the "P" button to see to the status of the photocell. 'H0' means that it is OFF , 'H1' means that is ON
32 Press the "∆" button to activate. 'H1' will be displayed.
33 Press the " " button to inactivate. 'H0' will be displayed.
34 Press P button to confirm and exit.
Note: If the photocells are not installed, make sure that the above-mentioned function is disabled. Otherwise, the operating mechanism will
35
open, but it will not close.
36 Automatic closing
37 Press and hold the P button until 'P1' is displayed
38 Press the "∆" button three times. 'P4' will be displayed
Press the "P" button to display the status of the automatic closing. 'b0' means no automatic shutdown, while 'b9' means the maximum
39
closing.
40 Press the "∆" button to increase or " " to decrease the delay by one minute.
41 Press P button to confirm and exit.
42 Locking the remote control
43 Press and hold the P button until 'P1' is displayed
44 Press the "∆" button four times. 'P5' will be displayed
45 Press "P" again. The current setting will be displayed: 'uL' - no lock of the remote control.
46 Press the "∆" button once. 'Lc' will be displayed - indicating the activation of the lock of the remote control.
47 Press P button to confirm and exit.
Opening the garage door
uL – opening of the door by pressing a pre-programmed button in the appropriate channel.
Lc – opening of the door by pressing a button with the padlock symbol
Closing the garage door
uL/Lc – pressing a pre-programmed button in the appropriate channel.
Cautions and Warnings
Operate the garage door only when you see everything within its moving range. Do not allow children to play with control mechanisms. Make sure that people are not within the range
of moving garage door. The same applies to animals or objects. The drive is designed for indoor installation and operation. The garage door and the control mechanism should be serviced
every year. Restoring the factory settings of the mechanical force involves steps described in sec. 24-26
1x
34
EN
and then a pre-programmed button in the appropriate channel.
1x
2x PIN +
2x
6x
← CH1 / 2x PIN + ← CH2
CH1
6x
CH2
CH3
99 - 11
––
P1
OP
OP
CL
CL
––
Su
SU
dL
P1
P2
F3
P1
P3
H0 - H1
H1
H0
P1
P4
b0 - b9
P1
P5
uL
Lc