Maintenance - Stomer Professional SFS-223 Bedienungsanleitung

English
Finishing sander
INTENDED USE
This tool is intended for dry sanding and fi nishing of wood,
painted surfaces, plastic and fi ller
TECHNICAL SPECIFICATIONS
PRODUCT ELEMENTS
1 On/Off switch
2 Dust bag
SAFETY
WARNING! Read all instructions. Failure to follow all in-
structions listed below may result in electric shock, fi re
and/or serious injury.
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Always keep the cord away from moving parts of the
tool; direct the cord to the rear away from the tool
• When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
• Use completely unrolled and safe extension cords with
a capacity of 16Amps (U.K. 13Amps)
• In case of electrical or mechanical malfunction, imme-
diately switch off the tool and disconnect the plug
• SBM Group can assure fl awless functioning of the tool
only when original accessories are used
• This tool should not be used by people under the age
of 16 years
• The noise level when working can exceed 85 dB(A);
wear ear protection
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
• Never use tool when cord is damaged; have it replaced
by a qualifi ed person
• Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to a
220V supply)
• This tool is not suitable for wet sanding
• Do not work materials containing asbestos (asbestos is
considered carcinogenic)
• When sanding metal, sparks are generated; do not use
dustbox and keep other persons and combustible material
from work area
• Do not touch the moving sanding sheet
• Do not continue to use worn, torn or heavily clogged
sanding sheets
• Wear protective gloves, safety glasses, close-fi tting
clothes and hair protection (for long hair)
• Take protective measures when during work dust can
develop that is harmful to one's health, combustible or ex-
plosive (some dusts are considered carcinogenic); wear a
dust mask and work with dust/chip extraction when con-
nectable
1
2
• Always disconnect plug from power source before
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live)
wire in the cord of this tool to the earth terminal of the
plug
• If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left unattended
• the dust suction requires the use of perforated sanding
sheets
• perforation in sanding sheet should correspond with
perforation in sanding foot
• replace worn sanding sheets in time
• always use the tool with the total sanding surface
covered with sanding paper
• before the sanding surface reaches the workpiece, you
should switch on the tool
• before switching off the tool, you should lift it from the
workpiece
• do not apply too much pressure on the tool; let the
sanding surface do the work for you
Your machine is double insulated in accordance with EN
50144; therefore no earthwire is required.

MAINTENANCE

Make sure that the machine is not live when carrying out
maintenance work on the motor.
Regularly clean the machine housing with a
soft cloth, preferably after each use. Keep the
ventilation slots free from dust and dirt.If the dirt
does not come off use a soft cloth moistened with soapy
water. Never use solvents such as petrol, alcohol, ammo-
nia water, etc. These solvents may damage the plastic
parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please con-
tact your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of the
packaging materials can be recycled. Take these materi-
als to the appropriate recycling locations. Take your un-
wanted machines to your local SBM Group dealer. Here
they will be disposed of in an environmentally safe way.
4