Diamond INNOVA 500 GBT Zusammenbau Und Betrieb Seite 7

Operator's guide:
1. Unpacking instructions
2. The handle
3. Internal cleaning
I
4. External cleaning
5. Connection to the mains
UK
6. Controls
7. Checking correct operation
D
8. Internal cleaning
9. Replacement of internal light bulbs
E
10. Replacement of the door magnetic gasket
F
!
WARNINGS
NL
It is most important that this instruction booklet is kept together with the appliance both for future
reference and for reasons of safety.
P
1. Adults should operate this appliance only. Do not allow children to use the controls or play with it. 2
is forbidden to modify in any way the main functions and characteristics of this appliance. . The electrical
S
installation of the appliance should be carried out by a qualified electrician or other competent person.
4 . Never attempt to carry out repairs unassisted. Inexpert repairs can cause serious damage and
DK
malfunction. . Assistance has to be provided by an authorized engineer only. Always use original spare 5
parts. . This appliance is not suitable for the storage of basic commodities not including food-stuffs. . The 6
FIN
manufacturers of this appliance accept no responsibility for the consequences of misuse in contravention
of these safety instructions. It further reserves the right to carry out improvements without prior notice.
B 8 . Avoid installing the cabinet directly in line with sunlight. . Nevere install the appliance near sources of
heat, such as radiators, stoves, etc.
11 .Ensure that the products displayed on the shelves and grills do not hang over the edges.
GR
air or products to be refrigerated should cause ice to form on the evaporator, we recommend stopping the
compressor and placing the goods in special refrigerated containers, kept at the same temperature, until
CZ
defrosting is completed;if this is not carried out the compressor will continue to operate leading to a
wasteful consumption of electricity and poor performance.
EE
it is indispensable to keep the door open at least 10 cm.
LV
LT
1. UNPACKING INSTRUCTIONS
CARDBOARD BOXES 1a.
H
WOODEN CRATE 1b.
between the appliance and pallet or crate. . Lift the appliance.
M
appliance on a flat, level surface. . Make sure there is nothing left in the package before disposing of it.
7 . Sort out the packaging materials in order to facilitate disposal (see fig. 1).
PL
2. THE HANDLE
SK
1. The handle can be found in a bag inside the appliance.
screws already inserted in the holes on the door post; wrench down the screws. . Apply the plastic insert
SLO and press down until it clicks into place (see fig. 2).
3. INTERNAL CLEANING
1. Clean the internal surfaces and glass panels with a soft sponge and a neutral detergent. . Wipe with a
soft dry cloth.
4. EXTERNAL CLEANING
1. Use the same products as used for internal cleaning.
panels and from the outer grids. (see fig. 3).
5. CONNECTION TO THE MAINS
1. Ensure that mains voltage and frequency are the same as those stated on the rating plate
to the appliance. . Ensure that the supply socket:
rated current as set out on the rating plate;
with In = rated value as stated on the rating plate; - differential with Id sensitivity = 30 mA.
there is no danger of explosion (AD) in the room. . Make sure the environment is suitable for the power
supply cable provided. The cable of the appliance is H05 VVF, designed for internal use. For installation in
other than internal settings, it will be necessary to replace the cable with the appropriate type (for example
H07 VVF for external settings).
rest in its correct position for at least 3 hours before hooking it up to the mains. . Insert the plug in the
socket (do not use three-way adapters and reduction adapters) (see fig. 4).
Operator's guide
10 . Keep the ventilation grills free from obstruction for at least 30 cm.
Cut surrounding tape. Remove the cardboard package by sliding it upwards.
Remove the nails from the wooden crate with care. . Insert forks of forklift truck
3
6
2
N.B.: If the equipment has been transported or stored overturned, let is
Maintenance manual (Page 48):
1. Cleaning the condenser
2. Replacement of a glass panel
3. Wiring diagram diagram of refrigeration unit
9
13 . If the appliance is not working and unused,
4. Remove the pallet or crate. . Place the
2. Fix the base of the handle using the two
2 . Remove the protective covering from the steel
a)
is properly earthed;
c)
complies with the IEC regulations:- thermal-magnetic switch
4
6
3
12 . If damp
2
5
3
2
(A) attached
b)
fulfils the requirements of the
3 . Ensure that
5
. It
7