Herunterladen Inhalt Inhalt Diese Seite drucken

Not Enough Or Too Much Detergent; No Suction; Insufficient Suction; The Brush Motor Or The Suction Motor Doesn't Stop - LAVOR Pro COMFORT S-R 66 Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 64
The brush motor thermal breaker tripped; the
motor overheated.
☺ Troubleshoot the cause (cords or similar items
that impede movement, surface too rough, etc.) and
press the reset breaker.
The transmission belt is broken.
☺ Replace it.
The motor relay or the brush motor is broken.
☺ Replace it.
9.2.4 NOT ENOUGH OR TOO MUCH DETER-
GENT
The detergent solution tank is empty.
☺ Fill the detergent solution tank after having em-
ptied the recovery tank.
The brushes or the machine has stopped.
☺ Activate the brushes and press the accelerator.
The flow adjustment lever is closed or almost clo-
sed.
☺ Adjust/increase the detergent solution outlet flow
as required.
The detergent solution filter is clogged.
☺ Clean the filter.
The detergent feed conduit is clogged in some
point.
☺ Clean out the conduit by removing the dirt.
The flow opening solenoid valve is burned.
☺ Replace it.

9.2.5 NO SUCTION

The suction hose is not connected to the squee-
gee.
☺ Connect it correctly.
The suction hose, the squeegee conduit or the
inspection compartment is clogged.
Clean out and remove any obstructions from the
conduits.
The suction motor is turned off.
☺ Activate it.
The recovery tank is full.
☺ Empty it.
The suction motor is not receiving electric power
or is burned.
☺ Check the connections and, for the latter case,
replace the motor.

9.2.6 INSUFFICIENT SUCTION

The recovery tank cover was not correctly tighte-
ned.
☺ Tighten it correctly.
The recovery tank drain hose plug is not perfectly
closed.
☺ Close it correctly.
The suction hose, the squeegee conduit or the
inspection compartment is clogged.
☺ Clean out and remove any obstructions from the
conduits.
9.2.7 THE BRUSH MOTOR OR THE SUCTION
MOTOR DOESN'T STOP
The relay switch is defective.
☺ Stop the machine, cutting off the main power sup-
ply and disconnecting the main battery connector,
and contact the technical service centre.
9.2.8 THE SQUEEGEE DOESN'T CLEAN OR
DRY EFFICIENTLY
The squeegee blades are worn or are dragging
solid dirt.
☺ Replace or clean them.
The squeegee adjustment is not correct; the
advancement must be exactly perpendicular to the
running direction.
☺ Adjust the squeegee.
The suction hose, the squeegee conduit or the
inspection compartment is clogged.
☺ Clean out and remove any obstructions from the
conduits.
9.2.9 THE BATTERY CHARGER DOESN'T
WORK
The battery charge doesn't start.
☺ Check that the battery charger is connected to the
battery. Consult the battery charger manual.
9.2.10 THE BATTERIES DO NOT CHARGE OR
DO NOT HOLD A CHARGE
At the end of the charging process, the battery is
not correctly charged (see the battery manufacture-
r's instruction-maintenance manual)
☺ Check the battery charger error message and
check the data indicated on the display (see the bat-
tery charger's instruction manual).
The batteries are new and do not generate 100%
of the rated performances.
☺ The accumulator reaches the maximum perfor-
mance after 20-30 complete charge cycles.
The electrolyte has evaporated and does not
completely cover the plates.
☺ Check the battery manufacturer's use and main-
tenance manual.
There are significant differences in density among
the various elements.
☺ Replace the damaged battery.
Always consult the battery and battery charger use
and maintenance manual. If this does not solve the
problem, contact the authorised technical service
centre.
The manufacturer CANNOT solve problems
caused by using batteries and battery char-
gers that were not directly supplied.
45

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis