Squeegee And Splash Guard Assem- Bly, Disassembly And Adjustment; Squeegee Assembly; Squeegee Disassembly; Squeegee Blades Replacement - LAVOR Pro COMFORT S-R 66 Bedienungsanleitung

work period, then disconnect the battery from the
battery charger.
Charge the battery during the night before using
the machine again.
Intermediate or incomplete charging while working
should be avoided.
If the machine is equipped with Pb-Acid batteries,
use a hydrometer to check the element liquid in-
tensity on a regular basis: if one or more elements
are discharged and the others fully charged, the
battery has been damaged and should be replaced
or repaired (refer to the battery service manual).
Close the element plugs and lower the top tank.
Hold the connectors with the hands; don't pull
them using the cables.
Reconnect the battery connector to the connector
on the machine.
7.2 SQUEEGEE AND SPLASH GUARD ASSEM-
BLY, DISASSEMBLY AND ADJUSTMENT
The squeegee is the main component that ensures
perfect drying.

7.2.1 SQUEEGEE ASSEMBLY

Lower the lifting system to avoid having to keep the
body raised while completing connections.
Loosen the connection knobs on the squeegee sup-
port (Photo G - 3).
Insert the openings of the squeegee body in the
brackets of the oscillating support.
Fully tighten the squeegee knobs of the support
(Photo G - 3) in order to block the squeegee on the
support.
Firmly insert the machine suction hose into the
squeegee body (Photo G - 5).

7.2.2 SQUEEGEE DISASSEMBLY

Lower the lifting system to avoid having to keep the
body raised while completing connections.
Disconnect the suction hose from the squeegee
body (Photo G - 5).
Loosen the connections connection knobs on the
squeegee support (Photo G - 3).
Pull back the squeegee body to detach it from the
brackets of the oscillating support.

7.2.3 SQUEEGEE BLADES REPLACEMENT

Disassemble the squeegee from its support (see
7.2.2)
Unscrew the knobs ( Photo G - 6 ), remove the
bolts and the metal bar holders of the squeegee
blades.
Remove the rubber blades from the squeegee body.
To assemble the new blades, place the metal bar
holders on the front blade; place them on the
squeegee body and insert the bolts in the holes of
the squeegee body.
Place the rear blade on the squeeegee body with
the the bolts in its holes; place the metal bar hol-
ders and block the blades screwing the fixing knobs
( Photo G - 6 ).
It's normal that the rear strap has to be extended
to centre the connection screws. This will bring it
under the correct tension to avoid folds on the floor
and dry correctly.

7.2.4 SQUEEGEE ADJUSTMENT

The knob screw on the squeegee support (Photo
G - 4 ) adjust the squeegee's inclination with re-
spect to the floor. The two screws on the sides, con-
nected to the rear wheels of the squeegee (Photo
G - 2 ), are to adjust the pressure of the squeegee
to the floor.
When the squeegee is perfectly adjusted, the rear
squeegee blade, sliding as it moves, bends in all
points forming an angle of 45° with the floor.
As the machine operates (advances), it is possible
to operate on the inclination knob and pressure
screws ( Photo G - 4 ; Phot G - 2 ) to adjust the in-
clination and pressure of the squeegee blades on
the floor.
Squeegee drying must be uniform along the entire
drying line: damp patches mean that drying is in-
sufficient; turn the adjustment knobs to optimise
drying.
7.2.5 SPLASH GUARD ASSEMBLY/DISAS-
SEMBLY
The splash guard is assembled to the brush plate
with a spring holder linked to the brush plate itself.
To disassemble the splash guard simply detach the
spring holder and pull the splash guard.
To reassemble, fix the splash guard in the brush
plate, and then hook the steel cable to one side of
the plate and the spring holder to the other side of
the brush plate.

7.3 ACCESSORY ASSEMBLY/DISASSEMBLY

(BRUSHES, PAD DRIVERS AND ABRASIVE
DISKS)
• Never use the machine if brushes or pad drivers
and abrasive disks are not perfectly installed.
Assembly:
Make sure that the brush plate is raised; otherwise
lift it by following the instructions provided in the
specific section.
Make sure that the ignition key on the control panel
is in position "0".
Bring the brushes (or the guide disks equipped with
abrasive disks) near the connections, under the
brush plate; lift them, bring them through the cen-
tering flange, and turn them opposite the rotation
direction until you hear the stable "click" connec-
tion.
• Do not allow the length of the rows of brushes to
become lower than 1 cm.
• Do not allow the thickness of the abrasive disks to
become less than 1 cm.
38