Jacuzzi sasha Montageanweisung Seite 24

(detail 4) Re-position the profiles resting against each other and
the shower frame, ensuring that they are fully inserted under the
couplers.
( 24, details 1-2) Place the silicone on the shower base
frame and apply the covers to the base, in the following manner:
- insert them underneath the lip seal of the glazing bead
so that
- they are positioned above the base frame and inside the metal
tank.
Check that they are resting against the front cover (see also
detail 4)
(detail 3) Place the silicone in the contact area between the
"L" shaped covers and the base area.
(detail 4) Also place the silicone in the contact areas between
the "L" shaped cover and the front area.
( 25, details 1-2) Place a line of silicone on the inner edge of
the covers and insert them between the glass panels and the base
frame, as indicated (resting against the front cover).
(detail 3) Place the silicone in the indicated areas.
Installing the upper inner covers
( 26) Fit the upper inner covers, as indicated.
Gasket assembly
( 27, details 1-2) After having measured the length, cut
some sections from the sealant roll which must be applied to the
inner edge of the following profiles:
- the glass panels/the small panels/ (lower, vertical and upper side).
- the glass panels/the large panels/ (lower, vertical and upper side).
NOTE: it is recommended to cut approx. 5 cm more of the sealant
than the nominal length and then remove any remaining length
once assembly is complete.
Installing the shower wall (1)
( 28) Position the lower wall so that it rests against the base
profile and attach it to the frame as indicated.
NOTE: route the equipotential lead upwards, fastening it, in prepa-
ration for subsequent connection.
( 29, detail 1) Draw the wall towards the mixer system and the
wall connections and connect it using the provided flexible pipes.
(detail. 2) route the shower cascade connection pipe upwards, fas-
tening it, in preparation for subsequent connection.
(detail 3) Carry out equipotential connection between the
frame terminal and the mixer system.
( 30, details 1-2) Carry out connection of the electrical
power supply to the indicated junction box; then connect the
display to the indicated cable.
(detail 3) Attach the display to the wall and assemble the cornice.
( 30, detail 1a) Connect one of the light cables (4) to the
cable coming from the adjacent structure.
( 30, detail 4) Layer the wall over the one underneath and
attach it as indicated.
Installing roofs
Sasha (Sauna / Hammam); Sasha white (Hammam)
( 31) Apply the metal corners to the roof, as indicated.
Sauna
Sasha:
( 32, detail 1-2) (
Unwind the sensor cable and bring it near the electronic box, as
indicated.
Sasha:
( 32, detail 3) (
tion the roof so that it rests on the relevant frame. Adjust its posi-
tion, by lifting it as much as is needed to move it outwards and close
any openings between frame and roof.
Sasha:
( 32, detail 4) (
nect the sensor cable to the terminal indicated.
Hammam
Sasha / Sasha white:
(
to the roof.
Sasha / Sasha white:
(
cable and bring it near the electronic box, as indicated.
Sasha / Sasha white:
(
it rests against the respective frame.
Adjust its position, by lifting it as much as is needed to move it
outwards and close any openings between frame and roof.
Sasha / Sasha white:
(
head to the hammam's mixing system.
Sasha / Sasha white:
(
ble to the terminal indicated.
Sasha (Sauna / Hammam); Sasha white (Hammam)
( 34) Fix the roof to the walls and apply the cover panels us-
ing soft double-sided tape and heat resistant silicone.
Shower:
( 35, detail 1) Position the roof so that the back of the roof
rests against the wood frame and the roof sides rest against the
adjacent profiles.
( 35, detail 2) After having checked the alignment of the
shower frame with adjacent frames, make holes in these afore-
mentioned frames which align with the holes in the shower
frame.
Then attach this frame to the adjacent frames.
24
Sasha white:
32W, detail 1-2)
Sasha white:
32W, detail 3) Posi-
Sasha white:
32W, detail 4) Con-
33, detail 1) Attach the shower head
33, detail 2-3) Unwind the sensor
33, detail 4) Position the roof so that
33, detail 5) Connect the shower
33, detail 6) Connect the sensor ca-