Inhaltszusammenfassung für Riello Burners RS 190/M
Seite 1
Zweistufig gleitender oder modulierender Betrieb Progressive two-stage or modulating operation Fonctionnement à deux allures progressives ou modulant MODELLO - MODELL TIPO - TYP CODICE - CODE MODEL - MODELE TYPE - TYPE 3866206 RS 190/M 836 T1 2916148 (2) - 03/2007...
DESCRIZIONE BRUCIATORE (A) 1 Testa di combustione 2 Elettrodo di accensione 3 Vite per regolazione testa di combustione 4 Pressostato gas di massima 5 Manicotto 6 Servomotore, comanda la farfalla del gas e, tramite una camma a profilo variabile, la ser- randa dell’aria.
BRENNERBESCHREIBUNG (A) BURNER DESCRIPTION (A) DESCRIPTION BRULEUR (A) 1 Flammkopf 1 Combustion head 1 Tête de combustion 2 Zündelektrode 2 Ignition electrode 2 Electrode d'allumage 3 Einstellschraube des Flammkopfes 3 Screw for combustion head adjustment 3 Vis pour réglage tête de combustion 4 Gas-Höchstdruckwächter 4 Max.
CAMPO DI LAVORO (A) La potenza del bruciatore varia in funziona- mento tra: • una POTENZA MASSIMA, scelta entro l’ area • e una POTENZA MINIMA, che non deve essere inferiore al limite minimo del dia- gramma: RS 190 /M = 470 kW Attenzione: il CAMPO DI LAVORO è...
REGELBEREICH (A) FIRING RATE (A) PLAGE DE PUISSANCE (A) Wahrend des Betriebs schwankt die Brenner- During operation, burner output varies between: La puissance du brûleur en fonctionnement leistung zwischen: varie entre: • a MAXIMUM OUTPUT, selected within area A, • einer HÖCHSTLEISTUNG, innerhalb •...
PRESSIONE GAS ∆p (mbar) La tabella a lato indica le perdite di carico min- RS 190/M ime lungo la linea di alimentazione del gas in funzione della potenza massima del bruciatore. Colonna 1 3970181 3970221 3970222 3970223 Perdita di carico testa di combustione.
GASDRUCK GAS PRESSURE PRESSION DU GAZ In der nebenstehenden Tabelle werden die The adjacent table shows minimum pressure Le tableau ci-contre indiquée les pertes de Mindestströmungsverluste entlang der Gas- losses along the gas supply line depending on charge minimales sur la ligne d'alimentation en zuleitung in Abhängigkeit der Höchstleistung the maximum burner output operation.
Forare la piastra di chiusura della camera di combustione come in (A). La posizione dei fori filettati può essere tracciata utilizzando lo sch- ermo termico a corredo del bruciatore. RS 190/M 325-368 M 16 LUNGHEZZA BOCCAGLIO (B) La lunghezza del boccaglio va scelta secondo le...
INSTALLATION INSTALLATION INSTALLATION KESSELPLATTE (A) BOILER PLATE (A) PLAQUE CHAUDIERE (A) Die Abdeckplatte der Brennkammer wie in (A) Drill the combustion chamber locking plate as Percer la plaque de fermeture de la chambre de gezeigt vorbohren. Die Position der Gewinde- shown in (A).
REGOLAZIONE TESTA DI COMBUSTIONE A questo punto dell’installazione, boccaglio e manicotto sono fissati alla caldaia come in fig. (B). È quindi particolarmente agevole la regolazione delle testa di combustione, regolazi- one che dipende unicamente dalla potenza massima del bruciatore. Perciò, prima di regolare la testa di combus- tione, bisogna fissare questo valore.
EINSTELLUNG DES FLAMMKOPFS SETTING THE COMBUSTION HEAD REGLAGE TETE DE COMBUSTION An dieser Stelle der Installation sind Flammrohr Installation operations are now at the stage A ce stade de l'installation, buse et manchon und Muffe gem. Abb. (B) am Kessel befestigt. where the blast tube and sleeve are secured to sont fixés à...
LINEA ALIMENTAZIONE GAS • La rampa può arrivare da destra o da sinistra, secondo comodità. • Le valvole del gas devono essere il più vicino possibile al bruciatore in modo da assicurare l'arrivo del gas alla testa di combustione nel tempo di sicurezza di 3 s.
GASZULEITUNG GAS LINE LIGNE ALIMENTATION GAZ • Die Armatur kann je nach Bedarf von rechts • The gas train can enter the burner from the • La rampe peut arriver par la droite ou par la bzw. links zugeführt werden. right or left side, depending on which is the gauche selon les cas.
INSTALLATION ELECTRIQUE REALISEE EN USINE SCHEMA (A) Bruciatore RS 190/M • Il modello RS 190/M lascia la fabbrica previsto per alimentazione elettrica 400 V. • Se l'alimentazione è 230 V, cambiare il colle- gamento del motore (da stella a triangolo) e la taratura del relè...
LAYOUT (A) Brenner RS 190/M SCHEMA (A) Burner RS 190/M • Die Modelle RS 190/M wird werkseitig für 400 Brûleur RS 190/M • Models RS 190/M leaves the factory preset for V Stromversorgung vorbereitet. • Le modèle RS 190/M quitte l'usine prévu pour 400 V power supply.
7- Pg 11 Forare, se si desidera aggiungere un bocchettone SCHEMA (B) Allacciamento elettrico bruciatore RS 190/M senza controllo tenuta valvole gas SCHEMA (C) Allacciamento elettrico bruciatore RS 190/M con controllo tenuta valvole gas VPS Il controllo tenuta valvole gas avviene subito prima di ogni avviamento del bruciatore.
Seite 22
Gasventile presse-étoupe 7- Pg 11 Bohren, falls man wünscht, noch LAYOUT (B) einen Stutzen einzusetzen Electrical connection RS 190/M burner with- SCHEMA (B) out leak detection control device Branchement électrique brûleur RS 190/M SCHEMA (B) sans dispositif de contrôle d'étanchéité...
Seite 23
- d : bianco weiss white blanc Il bruciatore RS 190/M lascia la fabbrica previsto per alimentazione elettrica 400 V. Se l'alimen- tazione è 230 V, cambiare il collegamento del motore (da stella a triangolo) e la taratura del RELÈ...
N.B. • Bei Dreieck-Schaltung mit 230 V- Spannung, moteur à 400 V, la protection est assurée quand Burner RS 190/M leaves the factory preset for 400 muß der Zeiger auf "MAX" gestellt werden. même. V power supply. If 230 V power supply is used, Obwohl die Skala des Wärmerelais nicht die...
REGOLAZIONI PRIMA DELL'ACCENSIONE PRESSOSTATO GAS DI MIN. PRESSOSTATO GAS DI MAX. PRESSOSTATO ARIA La regolazione della testa di combustione, aria e GAS-MINDESTDRUCKWÄCHTER GAS-HÖCHSTDRUCKWÄCHTER LUFT-DRUCKWÄCHTER gas, è già stata descritta a pag. 16. Altre regolazioni da fare sono: MIN GAS PRESSURE SWITCH MAX GAS PRESSURE SWITCH AIR PRESSURE SWITCH Aprire le valvole manuali poste a monte della...
EINSTELLUNGEN VOR DER ZÜNDUNG ADJUSTMENTS BEFORE FIRST FIRING REGLAGES AVANT L'ALLUMAGE Die Einstellung des Flammkopfs, von Luft und Le réglage de la tête de combustion, air et gaz, Adjustment of the combustion head, and air and Gas, ist bereits auf Seite 17 beschrieben worden. a déjà...
REGOLAZIONE BRUCIATORE Per ottenere una regolazione ottimale del bruci- atore è necessario effettuare l'analisi dei gas di scarico della combustione all'uscita della caldaia. Regolare in successione: 1 - Potenza all’accensione; 2 - Potenza MAX; 3 - Potenza MIN; D791 4 - Potenze intermedie tra le due; 5 - Pressostato aria;...
BRENNEREINSTELLUNG BURNER CALIBRATION REGLAGE BRULEUR Für die optimale Einstellung des Brenners soll- The optimum calibration of the burner requires Pour obtenir un réglage optimal du brûleur, il ten die Abgase am Kesselausgang analysiert an analysis of the flue gases at the boiler outlet. faut effectuer l'analyse des gaz d'échappement werden.
Regolazione dell'aria Variare in progressione il profilo finale della camma 4)(A) agendo sulle viti 7). - Per aumentare la portata d’aria avvitare le viti. - Per diminuire la portata d’aria svitare le viti. 3 - POTENZA MIN La potenza MIN va scelta entro il campo di lav- oro riportato a pag.
Lufteinstellung Adjusting air delivery Réglage air Über die Schrauben 7) das Endprofil des Progressively adjust the end profile of cam 4)(A) Modifier en progression le profil final de la came Nokken 4) (A) verändern. by turning the screws 7). 4)(A) en agissant sur les vis 7). - Zur Erhöhung Luftdurchsatzes...
5 - PRESSOSTATO ARIA (A) PRESSOSTATO ARIA 15)(A)p. 8 Eseguire la regolazione del pressostato aria LUFT-DRUCKWÄCHTER 15)(A)S. 8 dopo aver effettuato tutte le altre regolazioni del AIR PRESSURE SWITCH 15)(A)p. 8 bruciatore con il pressostato aria regolato a PRESSOSTAT AIR 15)(A)p. 8 inizio scala (A).
5 - LUFTDRUCKWÄCHTER (A) 5 - AIR PRESSURE SWITCH (A) 5 - PRESSOSTAT DE L'AIR (A) Effectuer le réglage du pressostat de l'air après Die Einstellung des Luftdruckwächters erfolgt Adjust the air pressure switch after having per- avoir effectué tous les autres réglages du brû- nach allen anderen Brennereinstellungen;...
CONTROLLI FINALI (con bruciatore funzionante) VISORE FIAMMA - SICHTFENSTER FLAMME • Scollegare un filo del pressostato gas di FLAME INSPECTION WINDOW - VISEUR FLAMME minima: • Aprire il telecomando TL: • Aprire il telecomando TS: il bruciatore deve fermarsi • Scollegare il filo comune P del pressostato gas di massima: •...
ENDKONTROLLEN (bei Brenner in Betrieb) FINAL CHECKS (with burner running) CONTROLES FINAUX (brûleur en fonctionne- • Einen Draht des Gas-Mindestdruckwächters • Disconnect one of the wires on the minimum ment) abtrennen: gas pressure switch: • Débrancher un fil du pressostat de seuil mini- •...
SIMBOLO (1) INCONVENIENTE CAUSA PROBABILE RIMEDIO CONSIGLIATO Il bruciatore non si avvia - Manca l'energia elettrica ......Chiudere interruttori - Controllare collegamenti - Un telecomando di limite TL aperto .
SYMBOL (1) FAULT PROBABLE CAUSE SUGGESTED REMEDY The burner does not start - No electrical power supply ......Close all switches - Check connections - A limiter control device is open .
SYMBOLE (1) INCONVENIENT CAUSE PROBABLE REMEDE CONSEILLE Le brûleur ne démarre pas - Absence de courant électrique ..... . Fermer interrupteurs - éontrôler fusibles - Une télécommande de limite est ouverte .