Nozzle Table; Adaptation To A Different Type Of Gas - Gorenje 426150 Gebrauchsanweisung

NOZZLE TABLE

Burner
Rated heat output (kW)
Reduced Rate (kW)
Gas consumption G30 (g/h)
Ø INJECTOR (mm)
G30/G31 28-30/37mbar
G30 50 mbar
G20 20mbar
Ø BY-PASS (mm)
G30/G31 28-30/37mbar
G30 50 mbar
G20 20mbar

ADAPTATION TO A DIFFERENT TYPE OF GAS

ART.NO. COUNTRY OF DESTINATION
426158
GB
453969
Burners
Coffe reductor
Pans
A SR
1,00 1,75
0,45 0,70
73 130
0,50 0,65
0,43 0,58 - M 0,80 - H6
0,72 - X 0,97 - Z 1,28 - H3
0,27 0,34
0,27 0,34
REG. REG.
CATEGORY
II2H3+
•
The gas burners are fitted a candle as flame failure device. If the burner flame is
extinguished accidentally or unintentionally, e.g. when some liquid boils over or
when there is draught in the room, gas supply is automatically cut off, thus
preventing the gas from being emitted into the room.
•
Gas burner cover should always be placed on the burner crown very carefully. Make
sure the slots on the burner crown are never obstructed.
1. Burner crown cover
2. Burner crown with the support for the burner cover
3. Candle flame failure device
4. Ignition candle
5. Nozzle
(only available with some models)
Use the extension when using a pan of a smaller diameter.
Place the extension on the grid above the auxiliary burner.
Correctly selected cookware will enable optimum cooking time and gas consumption.
•
Pan diameter is the most important parameter.
Use pans which have the right size for each burner.
•
Do not use small pans on large burners. The flame should not touch the sides of the
•
pan.
For smaller diameter pots and pans (coffee and tea pots, etc.), the power of the burner
•
being used has to be regulated in order to ensure that the flame laps the bottom of the
pot without spilling over.
For combustion, the gas also needs air. If a pan is too large, air supply to the burner is
•
insufficient; as a result, combustion effect is lesser.
Do not use pots with concave or convex bottoms.
•
Always place the pan right over the burner, not to one side. Otherwise it could tip over.
•
Place the pans on the pan supports, never directly on the burner. Make sure that the
•
pan supports and burner caps are correctly positioned before using the appliance.
Do not place large pans on the burners near the control knobs. These may be damaged
•
by the very high temperatures.
Never use two burners or heat sources to heat one single pan.
•
Do not use cast iron plates, griddles, earthenware casserole dishes, etc. for a long
•
period of time on maximum power especially on crystal glass gas hobs.
Pans should be placed on the hob carefully. Do not strike the hob and do not place
•
excessive weight on it.
Stainless steel working table can burnish when subjected to excessive heat. Therefore
•
we don't recommend prolonged cooking with soapstone, earthenware pans or cast iron
plates. Avoid the use of aluminum foil to protect the working table during cooking
operation.
R MW
3,00 3,30
1,00 1,50
218 238
0,85 0,85
0,80 - S 0,77 - F4
1,28 - T 1,35 - K
0,42 0,55
0,42 0,55
REG. REG.
GAS AND SUPPLY PRESSURE
G30/G31=28-30/37mbar ; G20=20mbar
10
TC
3,80
1,80
276
0,98
0,62
0,62
REG.