Fagor CFB90AXES Montage- Und Gebrauchsanweisung Seite 12

Automatic Calibration
Note: Carry out calibration when the hood is installed for the
first time.
Set the hood to OFF.
Press the "S" button.
The state of calibration in progress is shown by the flashing
"sensor" symbol.
Note: Do not activate the hood during calibration.
The sensor envisages an activation time which depends on
the calibration of the same, the necessary time varies
according to the hob selected.
Gas Hob: about 1,5 minutes
Induction Hob: about 13 minutes
Electric Hob: about 13 minutes
Calibration is necessary to stabilize the system, thus avoiding
malfunctions of the hood.
Calibration must be carried out with motor off.
Sensor test
It is constant during automatic working.
In case of failure the display shows an "Err" and the symbol
"sensor" both flashing (contact the technical assistance
office).
However the hood can be used in manual mode.
SPECIAL FUNCTIONS
Programming the Clock
The clock may be reset by pressing and holding the
"Timer" button for 5 seconds, then pressing the "-" and
"+" buttons to adjust the time.
The time setting mode is displayed by the two flashing
points.
The user may increase/decrease the time in steps of 1
minute; however, if the "-" or "+" button is pressed for 1
second, the time is decreased/increased in steps of 5
minutes. In this case, the control panel rounds the time
off to the nearest 5 minutes.
The user can end the clock resetting stage by pressing
the "Timer" button.
If none of the buttons are pressed for 1 minute, the control
panel accepts the set value and adds on 1 minute, then
begins to operate normally.
The clock can be displayed in 12h or 24h format.
To display the format set, press the "-" key for about 5
seconds until the time format being currently used is
displayed.
The cyclic selection takes place by pressing the "-" key
shortly.
Once the format has been selected, after 10 seconds the
system accepts the last choice made.
The symbol related to the format flashes for 3 times.
Grease filter warning
After 80 hours of operation, "Grease Filter" appears on the
display. When this text appears, the filter needs to be washed.
To reset the grease filter signal, set the hood to ON (at any
speed), press the "T1" key for 5 seconds until the prolonged
"beep".
When the hood is switched on again, the "Grease Filter"
disappears.
The grease filter counter will reset after this procedure is
complete.
Charcoal filter warning
After 320 hours of operation, "Charcoal Filter" appears on the
display. When this text appears, the filter needs to be
replaced.
To reset the charcoal filter signal, set the hood to ON (at any
speed), press the "T1" key for 5 seconds until the prolonged
"beep".
When the hood is switched on again, the "Charcoal
Filter" disappears.
The charcoal filter counter will reset after this procedure is
complete.
If both signals are active at the same time, just carry out the
resetting operation once.
Enabling/disabling the charcoal filter warning
Set the hood to ON (at any speed), press the "T1" key for 10
seconds.
"Able" and "Charcoal Filter": signal enabled
"None" and " Charcoal Filter ": signal enabled
Enabling/disabling the sound signal
Set the hood to ON (at any speed).
The sound signals may be activated or deactivated by
pressing and holding the "T2" button for 5 seconds.
If the sound signal has been activated, it should emit a
beep and the text "Snd" should appear on the display for
3 seconds.
If the sound signal has been deactivated, the text "Snd"
should appear on the display for 3 seconds and no beep
should be emitted.
Temperature alarm
The hood is equipped with a temperature sensor which
activates the motor at speed 2 in case the temperature in
the display zone is too high.
If the motor is OFF or at speed level 1 and the alarm
intervenes, the motor will move to speed level 2 and the text
"care" will appear on the display. While the appliance is in its
alarm operating status, the user may only increase the motor
speed (3 rd and 4 th levels). When the temperature of the
cooker hood returns to a level below the alarm threshold, the
motor will return to the status which was set before the alarm
condition occurred.
12