Specifications; Troubleshooting - XD P417.041 Handbuch

phone etc. Such devices will make the measurement inaccurate.
How to replace the battery
Open the battery compartment using a screw driver. Take out the old battery
and replace with a CR2032 new battery. Close the battery case tightly.
NOTE:
The + pole of the battery is upwards
Replace the battery when the LCD becomes dark
If there is no display or malfunction after replacing the battery, take the battery
out, wait 15 seconds or more and then put the battery back in.
How to replace the batteries in the chest strap:
Problem Cause
No LCD display Incorrect installation of
battery
No power
No display Belt is worn incorrectly
of heart rate
No power of chest belt
measuring or
battery
unsteady heart
rate signal Distance between chest belt
and watch is too long

Specifications:

1. Calendar clock:
Date and time format: hour, minute, second, month, day, year, week 12/24h
100 years auto-calendar: 2000-2099
Alarm: 1 daily alarm (hour-minute)
2. Stopwatch / Times
9H59M59.99S with 1/100 seconds
The first 10 lap time memory can be recalled
Lap time: 0-99
3. Heart rate monitor
Heart rate range: 40-240bpm
Resolution: 1bpm
Accuracy: ± 1bpm
GREEN region: heart rate percentage ≤ 60%
BLUE region: heart rate percentage between 60% and 85%
RED region: Heart rate percentage > 85%
Time for heart rate measurement: 99m59S
4. Environment
Operation 0°C - ± 50°C
Storage: -10°C - 60°C
At 10%-90% relative humidity
Water resistance: to 30m, but the buttons will not work in the water
5. Power source
Wrist watch: 1pc CR2032 3V Lithium battery
Chest belt: 1pc CR2032 3V lithium battery
PEDOMETER
Control buttons:
1. Volume and ON/OFF
2. Reset
3. Scan
4. Battery cover
5. Belt clip
6. Earphone Jack
7. Reset pedometer
Solution
8. LCD display
Re-install battery cor-
rectly Operation of the radio:
1. Open the battery cover by sliding and place one AAA battery with the polarity
Replace battery
+ facing up. Close the battery cover.
Wear belt correctly 2. Turn on the receiver by moving the volume button to your desired volume
3. Press the Reset button once to ensure the frequency is at the low end position (i.e.
Replace battery
FM 88 MHz)
4. Press the Scan button once. The radio will automatically search for broadcast
stations.
Keep distance within
5. Press the Scan button to select you desired radio station. When it reaches the high
80 cm
end position (i.e. FM 108 MHz), press the Reset button to bring it back to the low
end position. Then you can select you desired broadcast station again.
NOTE: if the Scan key is pressed several times and no broadcast station has been
reached, it signifies that the high end frequency (FM 108MHz) has been reached.
Operation of the pedometer:
Attach the pedometer to the waistband of your clothing. Start the measurement by
pressing the Reset Pedometer button. The pedometer will count up to 99.999 steps.
Trouble shooting:
Problem
Not all your steps
were detected
Obscure display
Ambient temperature
is too low
LCD is black
NOTE:
Do not disassemble the pedometer. This may damage the measuring accuracy
If there is no information or an error code on the display after removing the insulation
at the battery, please open the battery cover, take the battery out and put it battery
back in again.
Cause Solution
Pedometer is not mounted Mount the pedometer to
correctly your waist In the middle of
your body and stride at an
even pace
Low battery Replace the battery
Display will recover when the
temperature rises
Pedometer has been put under The LCD display will
direct sunlight or has operated recover in normal status in
too long in high temperature the shade