HQ Power VDPL601MH 14 Serie Bedienungsanleitung Seite 7

DM MX-512 con nnection
• When appl icable, conn
other side to the male
linked thro ough serial li
output con nnectors.
• Maximum recommend
of fixtures on a serial d
• A DMX term minator is re
an electric ally noisy en
signal by e electrical noi
and 3, whi ch is then p
Ge eneral
• Have a qua alified electr
• Connect th he device to
switched c circuit and ca
is used sol ely for 0% t
• The installa ation has to
Re eplacing the e fuse [8]
1. Only replac ce the fuse b
2. Before rep lacing the fu
3. Unscrew th he fuse hold
4. Remove th he old fuse a
5. Replace th e fuse holde
6. . Oper ration
Re fer to the ill ustrations o
Co ontrol Pane l Navigatio
• Access the e control pan
display [10 0]. From lef
bu utton function
<M MENU> used to ac
<U UP> scrolls thr
<D DOWN> scrolls thr
<E ENTER> used to se
• The contro ol panel disp
press <EN TER>.
• Use the <U UP> and <D
access the menu funct
or menu w without chang
Ma ain menu fu unctions
d isplay des scription
Set t DMX startin
...
bet ween 1 and
aut o run mode
aut o run mode
sou und controlle
run controlled
slav ve mode sele
pan n mode norm
tilt mode norma
disp play normal
V. 02 – 03/05/2 012
VD
nect an XLR c cable to the
3-pin XLR in nput [6] of
nking. The l inking cable
ed serial dat ta link distan
data link is 3 32 fixtures.
ecommended d for installa
nvironment ( (e.g. discos)
se. The DMX X terminator
lugged into the XLR outp
rician carry o out the elect
the mains w with the pow
annot be run n off a rheost
to 100% swi tch.
be approve d by an expe
by a fuse of the same ty
use, unplug mains lead.
er on the re ar panel of t
and install th e new fuse i
er in the hou using and tig
n page 2 of this manual
on
nel functions using the fo
ft to right:
ccess the me enu or to ret
rough the me enu options
rough the me enu options
elect and sto ore the curre
lay shows th he menu item
DOWN> butto ons to navig
tion currently y displayed
ging the valu ue, press the
p
<UP> <
ng address
512.
<D
- slow <EN
- fast <EN
ed mode <EN
<EN
ection <EN
mal <EN
al <EN
<EN
DPL601MHx x14
female 3-pi n XLR outpu ut of a contro
the VDPL60 01MHx14. M
should be a a dual core, s
nce is 500 m meters (1640 0 ft). Maximu
ations where e the DMX ca
). The termin nator preven
r is simply an n XLR plug w
put socket [ 5] of the las
rical connec tion.
er plug. All f fixtures mus
tat or dimme er circuit, ev
ert before th he device is t
ype and ratin ng.
the base wit h an approp
in the fuse h holder.
hten it.
.
our panel bu ttons [11] l
turn to a pre evious menu
in ascending g order
in descendin ng order
ent menu or option withi
ms you selec ct from the m
ate the men nu map and
or to enable e a menu opt
e <MENU> b button.
ress display sh
se elected DMX
OWN>
NTER>
NTER>
NTER>
NTER>
NTER>
NTER>
NTER>
NTER>
7
oller (not inc
Multiple VDP PL601MHx1 14's can be
screened ca ble with XLR R input and
um recomme
able has to r un a long dis
nts corruptio n of the digi
with a 120Ω resistor betw
st device in t the chain.
st be powere ed directly of
ven if the rhe eostat or dim
taken into se ervice.
riate screwd driver.
located direc ctly underne eath the
option
n the menu
menu map. T To select a m
menu option ns. Press <E
tion. To retu rn to the pre
hows re emark
address
au uto run mode
au uto run mode
so ound mode e
ru un mode ena abled
sla ave mode en
pa an reverse
til t reverse
di splay 180° r
cl.) and the
ended numb ber
stance or is in
ital control
ween pins 2
ff a grounde d
mmer chann el
menu item,
NTER> to
evious optio n
e - slow
e - fast
enabled
nabled
rotated
©Velleman n nv