Temperature Limitation; Maintenance - Hansgrohe Axor Starck Montageanleitung

Assembly
Attention! The fitting must be installed, flushed and
tested after the valid norms!
Adjustment
Correction is necessary if the temperature measured
at the take off point differs from the temperature
set on the scale. To adjust temperature proceed as
follows:
Turn the setting knob until water at a temperature
of 38° C comes out of the outlet. Loosen screw of
setting knob. Remove setting knob and turn to the
38° C position. Attach setting knob again and
tighten the screw.

Temperature limitation

The temperature is limited by the safety check to
38° C (100° F). If a higher temperature is required, it is
possible to override the safety stop by depressing the safety
button.
Safety Function
The desired maximum temperature for example max.
42° C can be pre-set thanks to the safety function
(please see page 25).
Technical Data
Operating pressure:
Recommended operating pressure: 0,1 - 0,5 MPa
Test pressure:
(1 MPa = 10 bars = 147 PSI)
Hot water temperature:
Recommended hot water temp.: 65° C
Rate of flow by 0,3 MPa:

Maintenance

There is no special maintenance for thermostats. The
non return valves (22) must be checked regularly ac-
cording to DIN EN 1717 in accordance with national
or regional regulations (at least once a year). At this
time, please also check the filter (20.1) situated on
the MTC-thermo-element (20). After assembling the
MTC-thermo-element, it is necessary to check the
water temperature at the take off point as described
under the headline „adjustment". Before the adjust-
ment, please check, if the warm water supply is
activated and the maximum temperature of the warm
water is available at the take off point.
English
max. 1 MPa
1,6 MPa
max. 80° C
approx. 26 l/min
To guarantee the smooth running of the thermostat, it
is necessary from time to time to turn the thermostat
from total hot to total cold.
Spare parts (see page 4)
1 handle for thermostat Starck /
Starck X
2 handle for thermostat
Carlton "lever"
3 handle for thermostat
Carlton "cross"
4 handle for thermostat Steel
5 handle for thermostat Montreux
6 handle for thermostat
Terrano "lever"
7 handle for thermostat
Terrano "cross"
8 handle for thermostat
Uno / Citterio M
9 handle for thermostat
Citterio "lever"
10 handle for thermostat
Citterio "cross"
11 handle for thermostat Massaud
12 face plate
13 face plate Starck X
14 face plate Massaud
15 face plate Montreux
16 face plate Citterio
17 face plate Citterio M
18 sleeve
19 sleeve Massaud
20 thermostat cartridge
21 noise reduction
22 non return valve
23 shut off unit
24 sub plate
25 fixing screw
26 sleeve
27 handle Starck / Citterio /
Massaud Citterio M
28 handle Uno / Terrano / Steel
29 handle Carlton
30 handle Montreux
31 extension set 25 mm
32 extension set 22 mm
33 extension set 22 mm
Citterio / Starck X
34 extension set 22 mm Citterio M
35 adapter for handle
36 adapter for handle
37 adapter for handle Massaud
10391XXX
17391XXX
17994XXX
35391800
16594XXX
37391XXX
37994XXX
38391XXX
39994XXX
39391XXX
18097000
96551XXX
97925000
98686000
98668XXX
96751XXX
98919000
96439XXX
98734000
94282000
94073000
94074000
94009000
96447000
96454000
96446XXX
96520XXX
96421XXX
96449XXX
98637XXX
13595000
13596XXX
97407XXX
98860000
96435000
96451000
98701000
11