Intended Use; Special Safety Instructions - Ayce NC800AG-125 Gebrauchsanweisung

INTENDED USE

This machine is intended for grinding and cutting metal with suitable accessories

SPECIAL SAFETY INSTRUCTIONS

Safety Warnings Common for Grinding, Sanding, Wire Brushing, Polishing or
Abrasive Cutting-Off Operations
a) This power tool is intended to function as a grinder. Read all safety
warnings, instructions, illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
b) Operations such as sanding, wire brushing, polishing or cutting-off are not
recommended to be performed with this power tool. Operations for which
the power tool was not designed may create a hazard and cause personal
injury.
c) Do not use accessories which are not specifically designed and
recommended by the tool manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least equal to the maximum
speed marked on the power tool. Accessories running faster than their
RATED SPEED can break and fly apart.
e) The outside diameter and the thickness of your accessory must be within the
capacity rating of your power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
f) Threaded mounting of accessories must match the grinder spindle thread.
For accessories mounted by flanges, the arbour hole of the accessory must
fit the locating diameter of the flange.
g) Do not use a damaged accessory. Before each use inspect the accessory
such as abrasive wheels for chips and cracks. If power tool or accessory
is dropped, inspect for damage or install an undamaged accessory. After
inspecting and installing an accessory, position yourself and bystanders
away from the plane of the rotating accessory and run the power tool at
maximum no-load speed for one minute. Damaged accessories will normally
break apart during this test time.
h) Wear personal protective equipment. Depending on application, uses face
shield, safety goggles or safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron capable of stopping small
abrasive or work-piece fragments. The eye protection must be capable of
stopping flying debris generated by various operations.The eye protection
must be capable of stopping flying debris generated by various operations.
The eye protection must be capable of stopping flying debris generated by
various operations. The dust mask or respirator must be capable of filtrating
180726_ayce_NC800AG-125_IM
particles generated by your operation. Prolonged exposure to high intensity
noise may cause hearing loss.
i) Keep bystanders a safe distance away from work area. Anyone entering
the work area must wear personal protective equipment. Fragments of
work-piece or of a broken accessory may fly away and cause injury beyond
immediate area of operation.
j) Hold the power tool by insulated gripping surfaces only, when performing
an operation where the cutting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator an electric shock.
k) Position the cord clear of the spinning accessory. If you lose control, the cord
may be cut or snagged and your hand or arm may be pulled into the spinning
accessory.
l) Never lay the power tool down until the accessory has come to a complete
stop. The spinning accessory may grab the surface and pull the power tool out
of your control.
m) Do not run the power tool while carrying it at your side. Accidental contact
with the spinning accessory could snag your clothing, pulling the accessory
into your body.
n) Regularly clean the power tool's air vents. The motor's fan will draw the dust
inside the housing and excessive accumulation of powdered metal may cause
electrical hazards.
o) Do not operate the power tool near flammable materials. Sparks could ignite
these materials.
p) Do not use accessories that require liquid coolants. Using water or other
liquid coolants may result in electrocution or shock.
Further safety instructions for operation
Kickback and Related Warnings
a) Maintain a firm grip on the power tool and position your body and arm to
allow you to resist kickback forces. Always use auxiliary handle, if provided,
for maximum control over kickback or torque reaction during start-up.
The operator can control torque reactions or kickback forces, if proper
precautions are taken.
b) Never place your hand near the rotating accessory. Accessory may kickback
over your hand.
c) Do not position your body in the area where power tool will move if kickback
occurs. Kickback will propel the tool in direction opposite to the wheel's
movement at the point of snagging.
82 83 |
GB
180726_ayce_NC800AG-125_IM