Mounting The Tool; Operating The Tool; Connecting To The Power Supply - PEUGEOT ENERGYDrill series Handbuch

4. Loosen the wing nut (3) or slide block (3) and slide
the end stop (4) along the drilling jig until it is firmly
against the left side of the workpiece. Tighten the
wing nut.
5. Check the accuracy by drilling a scrap workpiece.
Adjust if needed.
6. Hold with your hand or clamp the top surface of
the work-piece firmly to prevent it from lifting off the
table when the bit is raised.
Note: Wing nut (3) for EnergyDrill-16LA
Slide block (3) for EnergyDrill-20LA/FL

Mounting the tool

Note:
The drill press must be securely fastened by the two
base holes to a stand with heavy-duty fasteners.
This will prevent the drill press from tipping over,
sliding, or walking during operation.
1. Using the base of the drill press as a template
through the holes in the casting and drill the bench
with a Ø10 mm drill bit. (Fig. 18)
2. Note: If the stand has a tendency to move during
operation, fasten it securely to the floor. The
hardware used in the illustration are:
(1) Drill press base (2) Bolt (3) Flat washer (4)
Rubber washer (5) Work surface (6) Flat washer (7)
Lock washer (8) Hex nut (9) Jam nut.

Connecting to the Power Supply

Check that the power supply and plug receptacle are
in accordance with your drill press. Have a look at the
rating plate of the motor or the rating on the drill press.
Any change should always be carried out by a qualified
electrician.
WARNING: This machine must be earthed.
If not properly earthed this machine can cause an
electrical shock. Be sure that the power supply outlet
is earthed. If there is any doubt, have it checked by a
qualified electrician.
WARNING: Avoid contact with the terminals on
the plug when installing (removing) the plug to
(from) the power supply outlet. Contact will cause a
severe electrical shock.
USING AN EXTENSION LEAD
The use of any extension lead will cause some loss
of power. To keep this to a minimum and to prevent
overheating and motor burn-out, ask advice from a
qualified electrician to determine the minimum wire size
of the extension lead. The extension lead should be
equipped with an earthed type plug that fits the power
supply outlet at one end, and with an earthed type
socket that fits the plug of this machine at the other
end.

Operating the Tool

WARNING! Never connect the plug to power
source outlet until all installations and adjustments
are completed and you have read and understood
the safety and operational instructions.
INSTALLING THE DRILL BIT (Fig. 19)
1. Insert a drill bit (1) into the chuck far enough to
obtain maximum gripping of the chuck jaws (2).
(When using a small drill bit do not insert it so far
that the jaws touch the flutes-spiral grooves of the
drill bit.)
2. Make sure the drill bit is centered, then tighten the
chuck equally with the chuck key (3) by using all
three holes in succession.
Note: The drill bit can be released by using one hole
only.
ADJUSTING THE TABLE HEIGHT (Fig. 20)
1. Unlock the table bracket lock handle (2).
2. Turn the table crank handle (4) clockwise to raise
the table; anticlockwise to lower the table to the
required.
Note:
It is better to lock the table to the column in a position
so that the tip of the drill bit is just slightly above the top
of the workpiece.
3. Tighten the table lock handle (2).
TILTING THE TABLE (Fig. 21)
WARNING! To avoid injury from spinning work
or tool breakage, always clamp workpiece and
backup material securely to the table before
operating the drill press with the table tilted.
1. Turn the set screw (2) with the hex key
counterclockwise and loosen the lock nut (3) to
release it from the table bracket (5).
2. Loosen the table bevel lock bolt (1) and tilt the
table to the desired angle.
3. Tighten the table bevel lock bolt (1).
Note:
1. The set screw is for the 90° alignment of the table.
2. The bevel scale (4) is for quick bevel angle
reference only. Always check the angle before
drilling.
WARNING
!
Laser is radiated when laser guide is turned on.
Avoid direct eye exposure. Always unplug drill
press from power source before making any
adjustment.
LASER ON/OFF SWITCH (Fig. 30)
To turn the laser ON or OFF, press the rocker switch (3).
6