PEUGEOT ENERGYDrill series Handbuch Seite 6

Assembly
WARNING! Never connect the plug to power
source outlet until all installations and adjustments
are completed and you have read and understood
the safety and operational instructions.
Note: The loose parts can be found in the pulley cover.
INSTALLING THE COLUMN TO BASE (Fig. 2)
1. Position the base (1) on the floor.
2. Place the column (2) on the base, aligning the holes
in the column support with the holes in the base.
3. Locate the four long hex bolts (3) from the loose
parts bag.
4. Place a bolt in each hole through the column
support and the base. Tighten with an adjustable
wrench.
INSTALLING THE TABLE TO COLUMN (Fig. 3~8)
1. Insert the worm gear (1) into the table crank handle
hole (2) from inside the table bracket (3). Make sure
the worm gear (1) matches with the inside gear.
(Fig. 3)
2. Insert the table lock handle (4) into the hole at the
rear of the table bracket.(3) (Fig. 3)
3. Place the rack (1) in position inside the table
bracket (2), making sure the worm gear (3) on the
inside of the table bracket is engaged with the teeth
of the rack. (Fig. 4)
Note: Table removed from bracket in Fig. 3 & 4 for
clarity.
4. Slide the table bracket assembly together with the
rack onto the column.(Fig.4)
5. Engage the bottom of the rack (1) with the lip of
the column holder (2). Tighten the bracket lock
handle (3) to lock the table bracket assembly to the
column. (Fig. 5)
6. Install the collar (1) to the top end of the rack (2) on
the column. (Fig. 6)
IMPORTANT: The bottom of the collar must not be
pushed all the way down onto the top of the rack. Make
sure the top of the rack is under the bottom of the collar
and that there is enough clearance to allow the rack to
rotate freely around the column. Tighten the set screw
(3). (Fig. 6)
7. Install the table crank handle (1) to the worm gear
shaft (2) on the side of the table bracket (3). (Fig. 7)
8. Line up the flat side of the shaft with the set screw
(4) in the crank handle and tighten the screw with a
hex wrench. (Fig. 7).
9. Place the table (1) in the table arm assembly.
Tighten the table lock handle (2). (Fig. 8)
INSTALLING THE HEAD TO THE COLUMN (Fig. 9)
1. Carefully lift the head (1) above the column (2) and
slide it onto the column. Make sure the head slides
down over the column as far as possible. Align the
head with the base.
2. Using the hex wrench, tighten the two head lock set
screws (3) on the right side of the head.
INSTALLING FEED HANDLES (Fig. 10)
1. Screw the feed handles (1) into the right or left of
threaded holes (2) in the hub (3). Tighten. (Left hub
only applies for 20LA/FL series)
INSTALLING THE EXTENSION WING (Fig. 11)
1. Place the support bracket (1) onto the upper
tubes(2).
2. Place the flat washers (3) onto the hex head
bolts (4). Insert the bolt (4) into the upper tube (2),
and tighten.
3. Place the tube assembly under the table.
4. Place the clamp bolt (5) onto the set plate (6). Insert
the set plate assembly into the table and tighten.
INSTALLING THE EXTENSION WING (Fig. 11)
(EnergyDrill-16LA ONLY)
1. Place the flat washers (8) onto the hex head
bolts (9).
2. Insert the bolt (9) into the upper tube (7), and
tighten.
NOTE: If length adjustment is necessary, loosen
the clamp bolt (5) to the desired length and
tighten the clamp bolt.
INSTALLING THE CHUCK (WITH ARBOR)
1. Clean out the tapered hole in the chuck (1) with a
clean cloth. (Fig. 12)
2. Clean tapered surfaces on the arbor (2) and spindle
(3). (Fig. 12)
3. Push the chuck (1) onto the spindle arbor (2). Tap
gently to ensure seat. (Fig. 13)
4. Lower the spindle (2) by turning the feed handles (3)
anticlockwise until the slot (4) appears on the quill
(5). (Fig. 13)
5. Push the chuck and spindle arbor up into the
spindle, making sure the tang (6) (upper narrow end
of the spindle arbor shank) is engaged and locked
in the inner slot (7) of the spindle. This can be seen
through the outer slot (4) of the quill by rotating the
chuck and arbor until the two slots are aligned. (Fig.
13)
6. Open the jaw of the chuck (1) by rotating the chuck
sleeve clockwise. To prevent damage, make sure
the jaws are completely receded into the chuck.
(Fig. 14)
4
(20LA/FL ONLY)
(Fig. 12~14)