kbs FRL00 Installations-, Bedienungs- Und Wartungsanleitung Seite 60

60 - EN
PARAMETERS
To begin the procedure: To begin the procedure:
▪ ensure that no other procedure is in progress
▪ hold down and
▪ press
▪ press or
▪ press , display will show "PA"
▪ hold down and
PAR DESCRIPTION
SP SP Working Setpoint (see also r0)
measurement inputs
CA1 CA1 Offset cell probe
CA2 CA2 Offset evaporator probe
CA3 CA3 Offset condenser probe
Celsius grade decimal point
P1 P1
1 = YES
Temperature unit of measurement
P2 P2 0 = °C
1 = °F
Evaporator probe function
0 = probe absent
P3 P3
1 = defrosting probe and probe for evap. fan thermostatisation
2 = probe for evaporator fan thermostatisation
Enabling of condenser probe
P4 P4
1 = YES
P8 P8 Delay in display of variations in temperature detected by the probes
main regulator
r0 r0 Working Setpoint differential
r1 r1 Minimum working Setpoint
r2 r2 Maximum working Setpoint
Locking of working Setpoint calibration
r3 r3
1 = YES
Increase in temperature during Energy Saving function
r4 r4
(see also i5, HE1 e HE2)
r5 r5 Decrease in temperature during Overcooling function (see also r6)
r6 r6 Duration of Overcooling function (see also r5)
compressor protection system
C0 C0 Delay in switching on of compressor after the instrum. switches on
Min. time between 2 consecutive compressor start-ups
C1 C1 Also delay in compressor start-up after conclusion of cell probe error
(Pr1 code)
(4) (5)
C2 C2 Minimum duration of compressor switch off time
C3 C3 Minimum duration of compressor switch on time
Duration of compressor switch off during cell probe error
C4 C4
(Pr1 code) (see also C5)
Duration of compressor switch on during cell probe error (Pr1 code) (see
C5 C5
also C4)
Condenser temperature is higher than that at which the condenser
C6 C6
overheating alarm is activated (COH code)
Condenser temperature is higher than the limit at which the compressor
C7 C7
blocked alarm is activated (CSd code)
C8 C8 Compressor alarm delay locked (CSd code)
Number of operating hours in higher than the limit at which the need for
CA CA maintenance is signaled
0 = function absent
defrosting
Defrosting interval (only if d8=0, 1 or 2)
d0 d0
0 = interval defrosting will not be activated
for some seconds: the display will show "PA"
within 15 seconds to set "-19"
for many seconds: the display will show "SP".
(1)
(2)
(4)
(6)
(7)
(8)
min MAX M.U.
FRL00 FRL00
°C
r1 r2 °C
-25.0 25.0 °C
-25.0 25.0 °C
-25.0 25.0 °C
0 1 fl ag
0 1 fl ag
0 2 fl ag
0 1 fl ag
0 250 ds
0.1 15.0 °C
-99.0 r2 °C
r1 99.0 °C
0 1 fl ag
0.0 99.0 °C
0.0 99.0 °C
0 99 min
0 240 min
(3)
0 240 min
0 240 min
0 240 min
0 240 min
0 240 min
0.0 199.0 °C
0.0 199.0 °C
0 15 min
0 9999 h
0 99 h
FRL10 FRL10 FRL30 FRL30 FRL00 FRL00 FRL10 FRL10
(TN) 0/+10 (TNN) -2/+8
2 2 0 -2 -2
0 0 0 0 0
0 0 0 0 0
... 0 0 ... 0
0 0 0 0 0
0 0 0 0 0
0 0 0 1 1
... 0 0 ... 1
5 5 5 5 5
2 2 2 2 2
0 0 0 -2 -2
10 10 10 8 8
0 0 0 0 0
... 0 0 ... 0
3 3 3 3 3
30 30 30 30 30
1 1 1 1 1
1 1 1 1 1
1 1 1 1 1
0 0 0 0 0
10 10 10 10 10
10 10 10 10 10
... 80 80 ... 80
... 90 90 ... 90
... 1 1 ... 1
... 0 0 ... 0
8 8 8 6 6
FRL30 FRL30 FRL00 FRL00 FRL10 FRL10 FRL30 FRL30
(BT) -21/-18
-2 -21 -22 -20
0 0 0 0
0 0 0 0
0 ... 0 0
0 0 0 0
0 0 0 0
1 1 1 1
0 ... 1 0
5 5 5 5
2 3 3 2
-2 -21 -25 -20
8 -18 -15 -15
0 0 0 0
0 ... 0 0
3 3 3 3
30 30 30 30
1 1 1 1
1 1 1 1
1 1 1 1
0 0 0 0
10 10 10 10
10 10 10 10
80 ... 80 80
90 ... 90 90
1 ... 1 1
0 ... 0 0
6 5 5 5