Electrolux HSG1PH Bedienungsanleitung Seite 19

Important!
The appliance has an internal air cooling system (back and sides).
The air intake and outlet openings located under the appliance
must not be blocked with objects or cloths, otherwise excessive
overheating and damage to the equipment could occur.
5
See for minimal distances.
IMPORTANT
- During operation, pay attention to the hot
zones of the exterior surface.
- Do not place objects on the outlets located
at the top of the appliance. See
Warning!
The cooking zones remain hot. Even with the appliance swit-
ched off.
3
MICROWAVE INSTRUCTIONS
if any smoke is noticed, switch off and unplug the appliance and
keep the door closed in order to extinguish possible fl ames;
3.2 Instructions for use:
Warning: The appliance has an automatic lifting and locking
system of the lid. Also the upper heating element self adjusts to
the height of the food (3 inches maximum).Be sure that these
movements are never encumber.
Important: Before using the appliance make sure that the ap-
pliance is correctly installed and assembled (removable parts
fi xed in the right place), cleaned and connected to the power
supply.
START UP
Switch on the appliance by pressing the On/Off button. See
fi gure
7a
The appliance will start the preheating mode and display two
dot lines as the fi gure
During this time (up to 20 minutes) the appliance will not be
operational, i.e. the lid cannot be kept closed automatically.
The end of the preheating mode will be indicated by displaying
P1 as shown in fi gure
for operation.
OPERATING MODE
Warning:
The appliance has 4 preset programs. Make sure to use the
adequate program for the food to be cooked.
Choose the desired cycle by pressing one of the four program
buttons (see fi gure
The selected cycle will be shown in the display and with the
related light below the button pressed.
Place the food on the glass making sure that the food is fully
underneath the upper heating plate.
Important!
The glass and the upper heating plate are heating also when the
lid is opened. Therefore, do not leave the food on the glass long
before and long after the cooking cycle (risk of overcooking).
Fully close the lid and twist the handle until the automatic locking
system can be activated.
3
4
6a
and the appliance is ready
6b
).
7c
8
IMPORTANT - IF THE LID OR GLASS IS DAMAGED, THE AP-
PLIANCE MUST NOT BE USED UNTIL IT HAS BEEN REPAIRED
BY AUTHORIZED PERSONNEL;
WARNING - IT IS DANGEROUS FOR ANYONE EXCEPT
AUTHORIZED PERSONNEL TO CARRY OUT MAINTENANCE
OR REPAIR OPERATIONS INVOLVING THE REMOVAL OF ANY
COVER PROTECTING AGAINST EXPOSURE TO MICROWAVE
ENERGY.
PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE
MICROWAVE ENERGY :
- Do not attempt to operate this appliance with the lid open,
it can result in harmful exposure to microwave energy. It is
important not to defeat or tamper with the safety interlocks.
- Do not place any object inside the lid cover.
- Do not operate the appliance if it is damaged. It is particularly
important that the lid close properly and that there is no damage
to the glass
The appliance should not be adjusted or repaired by anyone
except properly qualifi ed service personnel.
The appliance will start the selected program showing the re-
maining time in minutes and seconds as fi gure
Important!
During this time you cannot:
- open lid
- change the program
and the only way to interrupt the cooking cycle and open the lid
is to shut off the appliance by pressing the On/Off button.
7a
The appliance can be restarted as described above.
A beep sound will indicate the end of the cycle and the lid opens
automatically.
Warning: During opening of the lid stay away and do not en-
cumber its movement.
Remove the food with a spatula.
3
Warning:
The glass and the upper heating plate are hot, risk of burning.
Important!
The glass and the upper heating plate are heating also when the
lid is opened. Therefore, do not leave the food on the glass long
before and long after the cooking cycle (risk of overcooking).
6c
STANDBY
The standby mode is an energy saving mode. After 15 min wi-
thout operation, the appliance will switch to the standby mode.
It is indicated by showing the 4 program button lights blinking.
To get out off the standby mode, press one of the program
buttons (P1 to P4). The appliance will return operational after a
preheating period.
The appliance is equipped with a performance regulation system
that guarantees a constant performance level in all environment
conditions. Therefore, it could happen that the appliance will
temporarily go in preheating mode during the operating mode.
TURN OFF
The appliance can be turn off in all regular modes by pressing the
On/Off button. During a period of about 5 minutes the appliance
will still have the cooling fans running; therefore the appliance
must not be unplugged in the time being.
6/9
6d
HSPP GB 09 2008