Specifications; Safety Instructions - Makita 3901 Betriebsanleitung

ENGLISH
1 Dust bag
2 Fastener
3 Dust nozzle
4 Pointer
5 Stopper
6 Hex nut
7 Adjusting screw
8 Loosen
9 Tighten
10 Lock lever
11 Angle guide
12 Knob

SPECIFICATIONS

Model
Blade size
Cutter blade
(Outer dia. x Width x Arbor dia.) ...... 100 x 4 x 22 mm
Circular saw blade
(Outer dia. x Arbor dia.) ....................... 110 x 20 mm
Max. cutting depth
Cutter blade .................................................. 20 mm
Circular saw blade ........................................ 25 mm
-1
No load speed (min ) .....................................11,000
Overall length ................................................ 307 mm
Net weight ........................................................ 2.8 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.

SAFETY INSTRUCTIONS

Warning! When using electric tools, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury,
including the following. Read all these instruc-
tions before attempting to operate this product
and save these instructions.
For safe operation:
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Don't expose power tools to rain. Don't use
power tools in damp or wet locations. Keep work
area well lit. Don't use power tools in presence of
flammable liquids or gases.
Explanation of general view
13 Pointer
14 Scale
15 Down
16 Up
17 Center of blade thickness
18 Fence
19 Lock lever
20 Angle scale
21 Pointer
22 Base
23 Set plate
24 Thickness of set plate: 4 mm
3.
3901
4.
5.
6.
7.
8.
9.
10. Connect dust extraction equipment
11. Don't abuse cord
12. Secure work
13. Don't overreach
25 Switch lever
26 Lock nut
27 Circular saw blade
28 Inner flange
29 Blade cover
30 Rubber facing
31 Cutter blade
32 Clamp screw
33 Limit mark
34 Brush holder cap
35 Screwdriver
Guard against electric shock
Prevent body contact with grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
Keep children away
Do not let visitors contact tool or extension cord.
All visitors should be kept away from work area.
Store idle tools
When not in use, tools should be stored in dry,
high, or locked-up place, out of the reach of chil-
dren.
Don't force tool
It will do the job better and safer at the rate for
which it was intended.
Use right tool
Don't force small tools or attachments to do the
job of a heavy duty tool. Don't use tools for pur-
poses not intended; for example, don't use circu-
lar saw for cutting tree limbs or logs.
Dress properly
Do not wear loose clothing or jewelry. They can
be caught in moving parts. Rubber gloves and
non-skid footwear are recommended when work-
ing outdoors. Wear protective hair covering to
contain long hair.
Use safety glasses and hearing protection
Also use face or dust mask if cutting operation is
dusty.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used.
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and
sharp edges.
Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to oper-
ate tool.
Keep proper footing and balance at all times.
7