THOMSON ROC1128LG Anleitung Seite 5

1. Press and hold the key [MUTE] and
[POWER] until the LED will be lit,
then release keys.
2. Enter the three codes from code Iist.
When the code input is finished, the
LED will turn off.
3. Please try to use the remote control.
lf it doesn't work well, please try other
codes: [002], [003], [004] ...
Note
lf the code is invalid, the LED flashes twice
and then lights up permanently. To exit the
setup, please press [MUTE].
5.2 FAST SEARCH
1. Press and hold the key [MUTE] and
[POWER] until the LED will be lit, then
release keys.
2. Press the key [CH+]. Each time you
press, the remote will search once.
When the code changes, you can test
if [POWER], [VOL+],[MENU],[0-9] keys
work well. If ok ,please press [ MUTE] to
save the code and exit.
3. lf it doesn't work well, repeat the fast
search by pressing [CH+].
5.3 CODE INQUIRY
Use the following method to find out which
code is currently set:
1. Press and hold [MUTE], then press
[POWER] until the LED will be lit, then
release keys.
2. Input [9].[9].[0] with number keys. The
LED will flash twice and goes off.
3. Press the number key 1 for the 1st digit
of the code. The LED will start to flash.
Count the LED flashes. The number of
flashes resemble the code's first digit.
Repeat this procedure for the 2nd and
3rd digit of the code:
2nd digit -> enter 2 -> count LED
flashes
3rd digit -> enter 3 -> count LED flashes
lf code number is [0] the LED will not
flash.
5.4 Compatible Remote Control Model
Due to too many Remote Control models, we
only Iist some of them below.
lf your remote control is similar to the drawing,
the replacement remote can control your TV
(Page 74).
5.5 Resetting to factory settings
Press and hold the [BACK] and [0] buttons for
about 5 seconds until the status LED flashes three
times and then goes out. The remote control is
now successfully reset to the factory settings.
Note
All keys with learnt codes or all copied keys,
as well as all remote control settings will
be deleted.
6. LEARN MODE
This remote control is equipped with a learning
function. Thus, you could learn functions of
your original remote to this remote control.
6.1 BEFORE STARTING LEARN MODE
• The batteries in the two remote controls
have to be in good condition. Replace them
if necessary.
• Place the remote controls with the infrared
diodes so that they point towards each other.
• Where necessary adjust the height of both
remotes so that infrared diodes are properly
aligned.
• The distance between the remote controls
should be about 3 cm.
ROC1128LG
Note
• Do not move the remote controls during
the learning procedure.
• Ensure that the room is not lit by
fluorescents tubes or low energy
consumption lamps since such light
sources could interfere with the copying.
• The 2 remote controls must be at least
1 meter away from any light source.
• During learning mode, if no key is
selected for more than 15 seconds, the
learning mode will exit automatically or
if no other remote signal is received.
• Each function key will hold only one
command. A new command to be learned
will automatically replace the previous one.
6.2 ENTER LEARN MODE
1. Press and hold the [MUTE] and [VOL+]
keys for approx. 5 seconds until the LED
will be lit.
2. Enter the code [9] [8] [0], the LED will flash
2 times and then remain on.
3. The remote control is now ready to learn
new commands.
6.3 LEARNING OF KEYS
1. Press and release the desired key on the
original remote control which you want the
command to be learned. The LED at your
replacement remote will flash to confirm
that the information has been received.
2. Then press and release the target key on
the remote control you want learned.
3
ORIGINAL
ca. 3 cm
5