Herunterladen Inhalt Inhalt Diese Seite drucken

Tig Welding; Remote Controls - Elettro TIG 1680 DC HF Betriebsanleitung

Lichtbogenschweissmaschinen
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 11
3.5 TIG
WELDING
This welding machine is suitable for welding stainless
ir
on, or copper using the TIG procedure. Connect the earth
cable connector to
the positive pole (+) of the welding
m
achine, and the clamp to the workpiece as close as
possible to the welding point, making sure there is good
electrical contact.
Connect the power connector of the TIG torch to the negative
pole (-) of the welding machine.
Connect the torch connector to the welding machine
connector Y.
Connect the torch gas hose fitting to the fitting X on the
machine, and the gas hose
regulator to the gas fitting A4 on the rear panel.
Turn on the m
achine.
Do not touch live parts and output terminals while the
machine is powered.
The first rime the machine is turned on, selec
using the push-buttons C
by means of the key I and the knob P as described in
paragraph 3.2 The flo
w of inert gas must be set to a value (in
liters per minute) approximately 6 times the diameter of the
electrode.
If you are using gas-lens type accessories, the gas
throughput may be reduced to approximately 3 times the
diameter of the electrode. The diameter of the ceramic
nozzle mus
t be 4 to 6 times the diameter of the electrode.
The most commonly used gas is normally ARGON, because
it is less costly than other inert gases, but you may also use
blends of ARGON with a maximum of 2% HYDROGEN for
welding stainless steel, and HELIUM or ARGON-HELIU
blends for welding copper.
These blends increase the heat of the arc while welding, but
are much more expensive.
If you are using HELIUM gas, increase the liters per minute
to 10 times the diameter of
10= 16 It./min of Helium).
Use D.I.N. 10 protective gla
from 75A up.
3.6 SAVING
You may save
parameters only after welding.
P
ressing the push-button W briefly makes a selection;
held down for
more than 3 seconds, it saves the data.
E
ach time it is turned on, the machine always shows the
last welding condition used.
3.6.1. Saving data from the PL program
Using the machine for the first time
When the machine is turned
s
ymbol PL; this disappears after 5 seconds, and a working
current is displayed. Follow the instructions
and 3.5, then proceed as follows to s
program P01:
• Briefly press the push-button W the message P01 will
appear flashing.
• Press push-button W for more than 3 seconds, until the
symbol P01 sto
ps flashing: at this point, the data have been
saved.
• Obviously, if yo
u wish to save in a program other than P01,
you should briefly press the push-button W as many times as
necessary to display the desired program. P01 will be
displayed
the next rime the machine is turned on.
PRESSING THE W PUSH-BUTTON BRIEFLY MAKES A
SELECTION, WHILE HOLDING IT DOWN FOR MORE
from the cylinder pressure
t the mode
and V and the welding parameters
the electrode (Ex. diameter 1.6 x
sses for up to 75A, and D.I.N. 11
on, the display shows the
in paragraphs 3.2
ave the data in the
THAN 3 SECONDS SAVES THE DATA.
3.6.2. Save from a free program
steel,
T
he operator may edit and save a selected program by
proceeding as follows:
• Press the push-button W briefly and select the desired
program number.
• The symbol of free programs is flashing.
• Press the push b
procedure and mode (paragraph 3.1).
• Turn the knob P and set the welding current.
• If the TIG procedure has been sel
LED O (post gas) by means of the push-button
the desired value via the knob P (paragraph 3.1.)
• If you wish to adjust the "slope" times or other
parameters, after making these adjustments wh
necessary in order to weld, follow the steps described
in paragraph 3.1.
• Weld, even briefly, and decide where to save
• To save in the p
button W for more than 3 seconds, until the numbe
flashing.
• To save in a different program, make your selection by
briefly pre
ssing the push-button W, then hold down the
push button W for more than 3 seconds.
3.6.3 Save from a saved program
B
eginning with a previously saved program, the operator
may edit the data in memory to upda
or to find new parameters to save in another program.
3.6.3.1 Update
M
• Alter turning on the machine,
be edited and edi
• Weld, even briefly.
• Hold down the W button
the save is confirme
flashing to steady).
3.6.3.2 Save in a n
• After turning on the machine,
be edited and edit them.
• Weld, even briefly.
• Briefly press the selecto
displayed.
• Hold down the W button until the save is confirmed
(program sy

4. REMOTE CONTROLS

The following remote contr
th
e welding current for this welding machine:
Item 570007 Foot control (used in TIG welding)
Item 535805 TIG UP/DOWN Torch.
Item 530330+ltem 570006 (used in MMA welding
Item 363307 Connection to simulta
torch and the pedal control.
Item 570007 may be used in any TIG welding mode with
this accessory.
Remote
regulate the we
maximum current set via the knob P.
Remote controls with UP/DOWN Iogic regulate the
welding current from the minimum to
The remote control settings are always active in the PL
program, while they are not active in a saved program.
10
uttons C and V and select the welding
reviously selected program, press the
select the parameters to
t them.
for more than 3 seconds, until
d (program symbol changes from
ew program
select the parameters to
r W until the desired program is
mbol changes from flashing to steady).
ols may be connected to adjust
controls
that
include
lding current from the minimum to the
ected, activate the
I, and set
ich are
r stops
te the program itself,
)
neously connect the
a
potentiometer
the maximum.

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis