33.16 · Technische Änderungen vorbehalten · Technical amendments reserved · Modifications techniques réservées
Gebrauchsanweisung
Instructions for use
Fiche d'utilisation
490
Anwendung
Mast mit Rohrbogen und Anschlussgewinde
G 1/2 · ISO 228 nach DIN EN 40-6.
EU-Konformitätszertifikat 0780-CPR-63018.
Produktbeschreibung
Mast besteht aus Aluminium und
Aluminiumguss,
pulverbeschichtet und lackiert
Zylindrisch abgesetzt, mit Rohrbogen und
Anschlussgewinde G 1/2 ISO 228
Erdstücklänge 800 mm
2 gegenüberliegende Kabeleinführungen
150 x 50 mm
Anschraubbare Grundplatte 250 x 250 mm
Mit eingesetzter Tür aus Aluminiumguss
Größe 300 x 82 mm
Türverschluss – Vierkant –
Schlüsselweite 8 mm
Gerätesteg mit Schutzleiteranschluss und
2 Schiebemuttern M6 zur Aufnahme eines
Anschlusskasten nach DIN 43628 / VDE 0660
- siehe BEGA Ergänzungsteile -
c 0780 – Konformitätszeichen
Windangriffsfläche: 0,51 m²
Gewicht: 23,0 kg
Sicherheit
Der Hersteller übernimmt keine Haftung für
Schäden, die durch unsachgemäßen Einsatz
oder Montage entstehen.
Werden nachträglich Änderungen an dem
Ergänzungsteil vorgenommen, so gilt derjenige
als Hersteller, der diese Änderungen vornimmt.
Lichtmast
Pole
Mât
Ø 48
Ø 133
Application
Pole with tube-bow and mounting bush G 1/2 ·
ISO 228 in accordance with DIN EN 40-6.
EU-declaration of confornity 0780-CPR-63018.
Product description
Luminaire pole made of aluminium and
aluminium alloy, powder coated and lacquered
Cylindrically stepped with tube-bow and
mounting bush G 1/2 ISO 228
Length of anchorage section 800 mm
2 opposite cable entries 150 x 50 mm
Screw-on anchor plate 250 x 250 mm
With inserted door made of aluminium alloy
Dimensions 300 x 82 mm
Lockable door – square spanner –
wrench size 8 mm.
C-clamp with earth conductor connection
and 2 sliding nuts M6 to accommodate a
connection box according to
DIN 43628 / VDE 0660
- see BEGA accessories -
c 0780 – Conformity mark
Wind catching area: 0.51 m²
Weight: 23.0 kg
Safety indices
The manufacturer is then discharged from
liability when damage is caused by improper
use or installation.
If any accessory is subsequently modified, the
persons responsible for the modification shall
be considered as manufacturer.
BEGA Lichttechnische Spezialfabrik
Hennenbusch · D - 58708 Menden
DIN EN 40
Utilisation
Mât avec crosse et raccord fileté
G 1/2 · ISO 228 selon DIN EN 40-6.
Certificat de conformité CE 0780-CPR-63018.
Description du produit
Mât fabriqué en aluminium et fonderie d'alu,
surface poudrée et laquée
Cylindrique-étagé avec crosse et raccord
fileté G½ ISO 228
Partie à enterrer 800 mm
2 entrées de câble opposées 150 x 50 mm.
Plaque de stabilisation à visser 250 x 250 mm.
Avec porte fabriquée en fonte d'alu
Dimensions 300 x 82 mm
Fermeture -goujon carré -
Ouverture de clef 8 mm
Rail intérieur avec raccordement de mise à la
terre et 2 écrous coulissants M6 pour la fixation
d'une boîte de connexion
DIN 43628 / VDE 0660
- voir accessoires BEGA -
c 0780 – Sigle de conformité
Prise au vent: 0,51 m²
Poids: 23,0 kg
Sécurité
Le fabricant décline toute responsabilité
résultant d'une mise en œuvre ou d'une
installation inappropriée du produit.
Toutes les modifications apportées à cet
accessoire se feront sous la responsabilité
exclusive de celui qui les effectuera.
!
70 993