Renfert hotty LED Bedienungsanleitung Seite 11

5.1 Setting the Temperature
scale to °C or °F
Please observe that all 230 V
units are pre-set to centigrade
(°C) and that all 120 V units
are pre-set to Fahrenheit (°F).
1. Steps 1-4 (point 5) must be
fulfilled before doing this.
2. Press and hold button (B).
3. The LED-Display now shows
C = degrees Celsius (fig. 8a)
or
F = degrees Fahrenheit (fig. 8b).
4. After 5 seconds, the display
changes between C and F and
vice versa. Release the button
when the required temperature
unit is shown on the display.
Following this, you will see the
nominal temperature displayed
shortly, then the actual tempera-
ture.
5.2 Setting the nominal
temperature
To set the temperature, press button
+/- (D) repeatedly until the required
value is displayed (fig. 9). This value
is saved automatically – even after
the unit is switched off.
Notice: Only use the button (B)
when turning the unit on and
off. If you turn the mains supply
off, the unit will not save any
values previously entered.
This however, will not affect
all other functions.
5.3 Dipping
(fig. 10)
• support the hand well.
• dip your object quickly into the
wax, past the preparation margin.
• pull the object back out in a slow
movement.
• hold shortly before the tip of the
die leaves the wax pot, allowing
excess wax to drip off.
6. Cleaning and
Maintenance
The hotty LED is maintenance free.
Wipe off the surface from time to
time using a damp soft cloth. Never
use detergents or solvents!
Never rinse the hotty LED
with running water!
Cold wax remnants can be removed
by carefully scraping them off.
Lightly warming the surface with a
hairdryer makes it easier to remove
any unwanted wax.
7. Spare Parts
All available spare parts are included
in the attached parts list.
8. Guarantee
Under proper use, Renfert warrants
the hotty LED for a period of 3 years.
Conditions for the fulfilment of this
warranty include the presentation of
original buyers receipt from a recog-
nised dealer. Components subject to
natural wear and tear are not inclu-
ded in this warranty.
Warranty becomes void in a case of
improper use, failure to observe ope-
rating, cleaning, maintenance and
connection instructions. Also in the
case of independent repairs or
repairs carried out by unauthorised
personnel, or if unauthorised spare
5.1 Setting the Temperature
scale to °C or °F
Please observe that all 230 V
units are pre-set to centigrade
(°C) and that all 120 V units
are pre-set to Fahrenheit (°F).
1. Steps 1-4 (point 5) must be
fulfilled before doing this.
2. Press and hold button (B).
3. The LED-Display now shows
C = degrees Celsius (fig. 8a)
or
F = degrees Fahrenheit (fig. 8b).
4. After 5 seconds, the display
changes between C and F and
vice versa. Release the button
when the required temperature
unit is shown on the display.
Following this, you will see the
nominal temperature displayed
shortly, then the actual tempera-
ture.
5.2 Setting the nominal
temperature
To set the temperature, press button
+/- (D) repeatedly until the required
value is displayed (fig. 9). This value
is saved automatically – even after
the unit is switched off.
Notice: Only use the button (B)
when turning the unit on and
off. If you turn the mains supply
off, the unit will not save any
values previously entered.
This however, will not affect
all other functions.
5.3 Dipping
(fig. 10)
• support the hand well.
• dip your object quickly into the
wax, past the preparation margin.
• pull the object back out in a slow
movement.
• hold shortly before the tip of the
die leaves the wax pot, allowing
excess wax to drip off.
6. Cleaning and
Maintenance
The hotty LED is maintenance free.
Wipe off the surface from time to
time using a damp soft cloth. Never
use detergents or solvents!
Never rinse the hotty LED
with running water!
Cold wax remnants can be removed
by carefully scraping them off.
Lightly warming the surface with a
hairdryer makes it easier to remove
any unwanted wax.
7. Spare Parts
All available spare parts are included
in the attached parts list.
8. Guarantee
Under proper use, Renfert warrants
the hotty LED for a period of 3 years.
Conditions for the fulfilment of this
warranty include the presentation of
original buyers receipt from a recog-
nised dealer. Components subject to
natural wear and tear are not inclu-
ded in this warranty.
Warranty becomes void in a case of
improper use, failure to observe ope-
rating, cleaning, maintenance and
connection instructions. Also in the
case of independent repairs or
repairs carried out by unauthorised
personnel, or if unauthorised spare