Cleaning, Maintenance And Ordering Of Spare Parts; Disposal And Recycling - EINHELL BG-CG 7,2 Li Bedienungsanleitung

Anleitung_BG_CG_7_2_Li_SPK7:_
GB
When to cut hedges:
As a general rule: hedges which loose their
leaves in the autumn should be cut in June and
October.
Evergreen hedges can be cut in April and August.
6.3. Changing the blades
Important. Risk of injury!
To remove the blades, raise the lug (Fig. 6/Item 1)
and push off the cover (Fig. 6/Item 2) in direction of
the arrow.
Once you have removed the blade you will be able to
see the toothed wheels of the gear unit (Fig. 7). Make
sure that no dirt gets into the gear unit when you
change the blade.
To assemble, proceed in reverse order.
When you fit the hedge cutter blade check the
position of the pin for the eccentric connector (Fig.
7/Item 1). Take the hedge cutter blade and slide the
eccentric mount (Fig. 8/Item 1) into position so that
the pin for the eccentric connector and the eccentric
mount fit together precisely when assembled. Slot the
hedge cutter blade onto the guide pins (Fig. 7/Item 2).
When you fit the grass cutter blade check the
position of the pin for the eccentric connector (Fig.
7/Item 1) again. Shift the eccentric mount (Fig. 9/Item
1) on the grass cutter blade to the left or the right to
find the position at which the pin for the eccentric
connector (Fig. 7/Item 1) and the eccentric mount
(Fig. 9/Item 1) match up.
7. Cleaning, maintenance and ordering
of spare parts
7.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the equipment
immediately after you use it.
Clean the appliance regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the
plastic parts in the appliance. Ensure that no
water can get into the interior of the tool.
The shears should be cleaned thoroughly every
time before and after use. A few drops of oil (for
example sewing machine oil) applied to the
blades improve the cutting performance.
However, never apply grease to the blades.
To guarantee a constant exact cut it is necessary
12
13.02.2009 10:26 Uhr Seite 12
that grass residues and dirt is removed also from
the top and bottom blades.
Important.
Because of the risk of injury or damage to
property, never clean the product with running
water, especially not with a pressure hose. Store
the cordless shears in a dry and frost-free
location. The storage place must be inaccessible
to children.
7.2 Servicing
For good cutting performance the blades should
always be sharp. They can therefore be re-
sharpened with a whetstone. In particular we
recommend to remove notches and ridges which
are produced on the blades by stones or the like.
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering replacement parts:
Please provide the following information on all orders
for spare parts:
Model/type of the equipment
Article number of the equipment
ID number of the equipment
Spare part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info
Grass cutter blade: 341062001001
Hedge cutter blade: 341062001002

8. Disposal and recycling

The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The
equipment and its accessories are made of various
types of material, such as metal and plastic. Defective
components must be disposed of as special waste.
Ask your dealer or your local council.