Kress 650 SPS Bedienungsanleitung Seite 7

1 Cut-in/cut-out switch
2 Electronic adjusting wheel
3 Hood
4 Saw bench
5 Parallel fence (optional accessory)
6 Tension lever
7 Pendulum stroke adjusting knob
8 Saw blade
9 Suction connection piece Ø 35
10 Stop lever
11 Power cable module
12 Locking key
13 Chip tearing protection (plastic)
14 Sliding block
15 Chip tearing protection (steel)
Technical data
Input watts
Output watts
Idle speed strokes/min.
Control range strokes/min.
Stroke height mm
Cutting depth into:
wood mm
soft steel mm
light metal mm
Angular cuts up to °
Weight kg
Use
This saw is a general-purpose jigsaw for all sawing jobs on
hardwoods, soft woods, coated woods, chipboard, ply-
wood, metal and plastics up to the given cutting depth.
Safety instructions and prevention of accidents
Before operating the machine, please read through the
operating instructions completely, follow the Safety
Instructions in this manual as well as the general Safety
Instructions for Power Tools in the accompanying
booklet.
Caution!
Always remove the mains connector from the ap-
pliance before changing the tool!
Never put your hands in the vicinity of the tappet or
saw blade (8) while the machine is running! Danger
of injury!
To avoid injuries, wear protective gloves when
changing the saw blade!
Starting position
Striking point
(= tense position)
Clamping saw blade
Rotate tension lever (6) as far as it will go and hold
it fast.
Insert saw blade (8) as far as it will go.
Release tension lever (6).
English
650 SPS
650
340
3200
500...3200
19
110
6
16
45
2.3
Important: (must be observed):
Press the jigsaw blade tip against the wooden
board, until tension lever (6) springs back to the
neutral position.
The secure clamping of the saw blade (8) is only en-
sured once the tension lever has sprung back to the
neutral position. The hood (3) can then be closed.
Unclamping saw blade
Rotate clamping lever (6) as far as it will go and
hold fast.
Remove saw blade (8).
Only original Kress saw blades as listed in the operat-
ing manual or in accordance with the following sketch
with a max. thickness of 1.5 mm may be used. This is
the only way to guarantee that the saw blade is secu-
rely fastened and reduce as far as possible the risk of
accidents by the jigsaw blades becoming loose.
Do not work with materials containing asbestos!
Outside power sockets must be protected with
residual-current-operated circuit-breakers (r.c.c.b.).
Do not drill holes into the housing to label the
machine. The protective insulation will be bridged.
Please use self-adhesive labels.
Always lead cables away towards the back of the
machine.
Double insulation
Our equipment is designed in accordance with European
regulations (EN standards) for the utmost safety of the
user. Machines with double insulation always carry the
international symbol. The machines do not require
earthing. A two-core cable is sufficient.
The machines are interference-suppressed in accordance
with EN 55014.
Initial operation
Before the first operation check that the mains voltage cor-
responds to that given on the machine nameplate.
Motor
At the heart of the jigsaw is a powerful universal motor with
welded collector which can cope with extended use of the
tool. The motor has a great power reserve. Since it is very
important for the motor to be uniformly well-ventilated, it is
of particular importance to pay special attention to the
maintenance and servicing instructions for removing dust
and dirt.
Clamping and unclamping the saw blades
The advantage of the clamping system is that saw blades
can be changed without tools. First push the cover (3)
up. Turn the tension lever (6) to open the quick-change
clamping system so that the saw blade (8) can be
inserted. Make sure that it is pushed back as far as it
can go. By releasing the tension lever (6) and then push-ing
in the direction of the tappet, it is automatically fixed
in position, and the tension lever (6) returns to the neutral
position.
When unclamping the saw blade (8), it is released from the
fixed position by turning the tension lever (6). It can then be
removed from the tappet.