Inhaltsverzeichnis
Werbung
ANTI-SKATING ADJUSTMENT
TO ADJUST THE ANTI SKATING MECHANISM, TURN THE ANTI-SKATE KNOB
SO THAT THE NUMBER CORRESPONDING TO THE REQUIRED TRACKING
FORCE IS OPPOSITE THE INDEX LINE. THE NUMBERS ON THE ANTI-
SKATE KNOB CORRESPOND TO 1G OF TRACKING FORCE.
•
PRESS FUNCTION BUTTON TO SELECT "PHON" ON DISPLAY.
•
REMOVE THE STYLUS PROTECTOR.
•
BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM REST PART BEFORE
OPERATING AND RE-SECURED AGAIN AFTERWARDS.
•
PUSH THE LIFT LEVER UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK, AND THEN
SLOWLY MOVE IT TO THE RECORD SIDE. THE PLATTER WILL START TO ROTATE.
•
PUT DOWN THE LIFT LEVER TO DROP THE TONE ARM AND TOUCH THE RECORD GENTLY. PHONO
PLAYING STARTS NOW.
•
PUSH THE LIFT LEVER UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK, NOW PLATTER
WILL STILL BE ROTATING BUT PHONO PLAYING WILL STOP. TO CONTINUE THE PLAYING, THE
USER NEEDS TO PUT DOWN THE LIFT LEVER.
•
PRESS 33RPM SPEED SELECT OR 45RPM SPEED SELECT BUTTON DEPENDING ON THE RECORD
TO BE PLAYED, BUTTON INDICATOR WILL LIGHT UP.
•
PRESS START / STOP BUTTON, TURNTABLE WILL STOP ROTATING GENTLY. PRESS START / STOP
BUTTON, TURNTABLE WILL ROTATE AGAIN.
•
STROB DOTS ON THE TURNTABLE PLATTER FOR SPEED CHECKING. UPPER TWO ROWS FOR
50HZ, LOWER TWO ROWS FOR 60HZ. BIGGER DOTS FOR 45RPM, SMALLER DOTS FOR 33RPM.
SUITABLE DOTS WILL KEEP STABLIZED IF THE SPEED IF CORRECT. ADJUST SPEED BY PITCH
CONTROL SLIDER (+/-10%).
• PRESS TARGET LIGHT SWTICH, TARGET LIGHT WILL LIGHT UP; PRESS TARGET LIGHT SWTICH
AGAIN, TARGET LIGHT WILL BE OFF.
•
USE THE 45 RPM ADAPTOR IF REQUIRED.
•
ADJUST THE VOLUME TO THE DESIRED LEVEL.
•
AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING, TONE ARM WILL
AUTOMATICALLY RETURN TO THE TONE ARM REST PART. TRIGGER THE EJECT SWITCH DURING
RECORD PLAYING, TURNTABLE WILL STOP GENTLY AND TONE ARM WILL UTOMATICALLY
RETURN TO THE TONE ARM REST PART.
PHONO ENCODING
1. PRESS FUNCTION BUTTON TO SELECT "PHON" ON DISPLAY AND THEN
INSERT MEMORY DEVICE (USB DRIVE, SD OR MMC CARD).
2. PRESS THE REC BUTTON, IT WILL TAKE 3-5 SECONDS TO READ MEMORY
DEVICE. THEN USB OR SD ICON WILL BE FLASHING.
3. PRESS SKIP DOWN
DESIRED MODE (USB OR SD) FOR ENCODING. THEN PRESS THE REC
BUTTON AGAIN TO CONFIRM. AND THE SYSTEM IS STARTING THE ENCODING MODE AFTER FEW
SECONDSS.
4. IF ONLY USB DRIVE OR SD/MMC CARD IS INSERTED, STEP 3 CAN BE SKIPPED.
5. THE USB OR SD ICON WILL BE FLASHING ON THE DISPLAY DURNIG ENCODING.
6. TO FINISH ENCODING, PRESS STOP
TO PHONO MODE.
REMARK:-
•
THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLYING TIME OF THE PHONO
•
THE RECORDING FORMAT IS PRESET AT – MP3 BIT RATE : 128 KBPS
BUTTON OR SKIP UP
BUTTON AND DISPLAY WILL SHOW "END" AND RETURN
BUTTON TO SELECT
21
Werbung
Inhaltsverzeichnis
