Restore Default Settings; Tips For Best Results; Available Accessories - Audio-Technica ATW-T1802 Installation Und Betrieb

OM1800Ser_dual(europ).qxd:Layout 1
14

Restore Default Settings

E
N
Wireless Essentials ® Microphones and Cables
(all Wireless Essentials accessories are
terminated for use with UniPak™ transmitters)
1/10/07 14:35 Page 14
Operating theTransmitter
1. A "PRESET" selection in the menu allows you to reset all transmitter functions to their
factory-default values.
2. Press the Set button once to move to Menu mode.
3. Press the Up arrow twice to move to "PRESET" in the LCD window.
4. Press the Set button once and "LOAD" will appear in the LCD.
5. Press and hold the Set button until "DEF" appears in the LCD.
6. Press and hold the Set button until "LOADED" appears briefly in the LCD. The window will
then revert to "PRESET" .
7. Press the Down arrow once to move to "QUIT" .
8. Press the Set button once to exit the Menu mode and return to normal operation, with all
factory-default settings restored.

Tips for Best Results

1. Use only fresh alkaline batteries. Always replace all batteries.
Do not use "general purpose" (carbon-zinc) batteries.
2. Position the dual-channel receiver so that it has the fewest possible obstructions between it
and the normal location of the transmitters. Line-of-sight is best.
3. The transmitters and the dual-channel receiver should be as close together as conveniently
possible, but no closer together than three feet.
4. The receiver antennas should be in the open and away from any metal.
5. Each transmitter-receiver pair must be set to the same frequency.
6. Only one transmitter on a given frequency should be "on" at a time.
7. The power switch on the transmitter has four positions: "Ext.," "Off" ,"1" and "Both. "
8. If the "Out Level" of either receiver channel is set too high, it may over-drive the input of the
camera/mixer or clip the output of the receiver, causing distortion. Conversely, if the receiver
output is set too low, the overall signal-to-noise ratio of the system may be reduced.
9. You need to change channels 1) when a strong interference signal is received, 2) when the
channel breaks down, or 3) during multiple-system operation in order to select an interference-
free channel. Always turn the units off before changing frequencies.
10. Turn the receiver and transmitter off when not in use. Remove the batteries during long-term storage.

Available Accessories

AT829cW
MT830cW
MT830cW-TH
AT831cW
AT889cW
AT892cW
AT892cW-TH
AT892cW-CO
AT898cW
AT899cW
AT899cW-TH
ATM350cW
ATM73cW
ATM75cW
PRO8HEcW
PRO35cW
U851cW
U857ALcW
AT-8319
AT-8317
Receiver Accessories
RF Cables
AC12
AC25
AC50
AC100
Transmitter Accessories
ATW-RMS1
ATW-RCS1
Visit www.audio-technica.com for detailed information on all of our wireless accessories.
Cardioid condenser lavalier microphone
Omnidirectional condenser lavalier microphone
"Theater" model, same as MT830cW except beige-colour mic and cable
Cardioid condenser lavalier microphone
Headworn noise-cancelling condenser microphone
headworn omnidirectional condenser microphone
MicroSet ®
"Theater" model, same as AT892cW except beige-colour mic, earset and cable
"Theater" model, same as AT892cW except cocoa-colour mic, earset and cable
Subminiature cardioid condenser lavalier microphone
Subminiature omnidirectional condenser lavalier microphone
"Theater" model, same as AT899cW except beige-colour mic and cable
Cardioid condenser instrument microphone
Headworn cardioid condenser microphone
Headworn cardioid condenser microphone
Headworn hypercardioid dynamic microphone
Cardioid condenser instrument microphone
Cardioid condenser boundary microphone
Cardioid condenser gooseneck microphone
Hi-Z instrument/guitar cable with 1 / " phone plug
4
Connecting cable for UniPak transmitter with an XLRF-type input connector,
for Lo-Z microphones with XLRM-type output terminations
Low-loss design, 50 ohm impedance, with BNC-to-BNC connectors:
RG58-type cable (4 m)
RG8-type cable (8 m)
RG8-type cable (16 m)
RG8-type cable (33 m)
Remote mute switch designed to be installed between a wireless microphone
using an HRS-type connector and its associated body-pack wireless transmitter
Remote momentary-mute/cough switch designed to be installed between a
wireless microphone using an HRS-type connector and its associated body-pack
wireless transmitter