Restore Default Settings - Audio-Technica ATW-3110a Installation Und Betrieb

Vorschau ausblenden Andere Handbücher für ATW-3110a:

Installation und betrieb (125 Seiten)

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

Inhalt

126

Inhaltsverzeichnis

Verfügbare Sprachen

Transmitter Controls And Functions (continued)

Power/Mute Locks

Programmable Power/Mute Locks limit the functioning of the Power/Mute button as

desired for particular users and/or applications. Power can be locked On; Mute can be

locked Off. Selection of the desired locks, if any, is made through the function menu:

Setting

Description

NO.LOC

The normal Power and Mute functions are fully operational.

ALL.LOC

Both the Power and Mute functions are locked into their status as of

the time "ALL.LOC" is applied.

(Power On, and Mute either On or Off.)

Note: ALL.LOC must be re-accessed and the setting changed to turn

the transmitter off.

MUT.LOC

In this mode, the audio cannot be muted. The Power functioning is

unaffected. (If MUT.LOC is applied while the transmitter is muted,

pressing the Power/Mute button once will return to un-muted

operation; thereafter the Mute function is disabled until the setting is

changed again.)

PWR.LOC

Power is locked On as of the time "PWR.LOC" is applied. The Mute

functioning is unaffected. Note: When in the PWR.LOC mode, the

transmitter may be turned off by: (1) Re-accessing the . LOC Menu

and changing the setting, or (2) Removing and re-installing the

batteries. When the transmitter is turned on again, it will power-up in

the NO.LOC mode. (Only the PWR. LOC function will change when

batteries are removed; all other settings remain stored in memory.)

If an attempt is made to take an action that currently is locked out,

the LCD will display "LOC.KED" briefly, then return to its previously-

displayed contents.

Audio Input Selector

The UniPak™ body-pack transmitter provides input connections for both low-

impedance (Lo-Z) microphones and high-impedance (Hi-Z) instruments. A wide range

of Audio-Technica Wireless Essentials™ microphones and cables is available pre-

terminated with the appropriate professional latching connector. (See page 13.)

Selection of the desired input – microphone or instrument – is made through the

function menu. Depending upon the input selected, a small "MIC" or "INST" will show

in the LCD window, just below the frequency. (In the handheld transmitter, only

will show in the LCD window.)

Downloaded from

www.Manualslib.com

manuals search engine

Setting Audio Input Level

ATW-T310 and ATW T341 transmitter

A 4-position audio input gain setting, selected through the function menu, serves to

match the audio input level to the transmitter for best modulation with minimum

distortion.

Available choices are +12 dB, +6 dB, 0 dB and –6 dB. The default value is +6 dB. Select

the highest setting that does not result in over-modulation with the highest

audio/instrument input levels (an AF indication on the receiver no higher than "0");

watch the receiver's "AF" meter "+3/+6" indications and the Alert light to make certain

they are not triggered by the highest audio levels.

The transmitter's normally-on red LED power indicator will blink off if the peak audio

input exceeds the maximum desirable level.

ATW-T371 transmitter

A 3-position audio input gain setting, selected through the function menu, serves to

match the audio input level to the transmitter for best modulation with minimum

distortion.

Available choices are +12 dB, +6dB and 0dB. the default value is +6 dB. In addition, a

mechanical pad switch on the condenser capsule (inside the screw-on wire mesh

grille) can provide another 6dB of attenuation. For best performance, adjust the input

level using the function menu choices, keeping the capsule´s mechanical switch at

0dB. If more audio attenuation is needed, set the capsule´s pad switch to -6 dB.