Herunterladen Inhalt Inhalt Diese Seite drucken

Rear Panel Features; Cd Player Features - Numark CDN55 Kurzanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

REAR PANEL FEATURES

1.
CONTROL CABLE CONNECTOR – Plug
in the 8-pin cable included in here to
connect the remote control and main CD
unit together.
2.
POWER PLUG CONNECTOR – Plug your
supplied power cord in here.
3.
RCA AUDIO CONNECTORS – Connect
your CD player to your mixer from this
line-level output.

CD PLAYER FEATURES

1.
POWER SWITCH – Turn the unit on and off with this button. The unit should always be shut down with this button first
before any external power is removed. Typically it is recommended that the CD player is powered on before amplifiers
and powered off after amplifiers.
2.
EJECT (Disc Tray Open/Close) – Press to load or eject the disc. Each press will open or close the disc tray on the
transport.
NOTE: Tray will not open unless the disc has been paused. Tray will automatically close after 10 seconds.
3.
CD DRAWER – Place your CDs you wish to play in here. This unit is designed to play commercially available CDs and
properly burned and finalized CD-Rs. Due to variances on the specification of certain CD burners and CDs, some
homemade CDs may not play properly. We recommend burning CDs at the minimum speed possible for the best
performance.
4.
PLAY/PAUSE (Play/Pause Button) – Each press of the Play/Pause Button causes the operation to change from play to
pause or from pause to play. Pressing Play after Pause sets a new cue point.
5.
CUE – Pressing the CUE button during playback returns the track to the position to the cue point and pauses playback.
(See PLAY, PAUSE, & CUE OPERATIONS for more information.) For temporary play and effect, press and hold CUE
to play the track from the cue point. Releasing it will return to the cue point and pause playback.
6.
STUTTER – Starts the music from the cue point.
7.
LOOP IN – Used for setting a start loop point and new hot cue points during playback.
8.
LOOP OUT – Used for setting the end loop point and releasing the loop action.
9.
RELOOP / STUTTER – Used for either repeating a previously set loop or seamlessly stuttering on the last set hot cue
point.
10.
TRACK (Track Buttons) – Used to select the track to be played.
11.
SGL – Will cause just a single track to play or all tracks in order by pressing once or twice.
12.
TIME (Time Button) – Switches the time display between elapsed playing time and remaining time on the track and
remaining time on the entire CD.
13.
PITCH BEND / JOG WHEEL – The jog wheel serves two functions depending on its current mode.
a)
If a track is not playing, the wheel will search slowly through a track's frames. To set a new frame cue point,
rotate the wheel then begin playback when you have determined the proper position. Press CUE to return to that
cue point.
b)
If a track is playing, the wheel will temporarily bend the pitch of the track.
temporarily speeds it up while rotating it counterclockwise slows it down. This is a useful tool for beat-matching
(see MATCHING TEMPOS & BEATS).
14.
SEARCH – Pressing this button allows you to use the wheel and rapidly scan the music to find a cue point. The search
function automatically shuts off after 8 seconds of non-use or you may toggle it off.
15.
PITCH SLIDER – The pitch can be changed up to ±16% by moving the sliding fader.
16.
PITCH (Pitch Button) – Activates the pitch slider and adjusts the amount of control the pitch slider has on the overall
speed of music. Tapping the button will toggle slider between 8% and 16% pitch ranges. Holding the button for three
seconds will turn off Pitch.
17.
PITCH RANGE LEDs – Indicates current pitch range.
18.
LCD – Indicates all the functions, as they are occurring, with the CD. These functions are explained in the next section.
4
Rotating the wheel clockwise

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis