Channel List; Use Of The Channel List; Setting Of Parental Control Settings; Electronic Program Guide (Epg) - AEG TV4500ZM Bedienungsanleitung

Channel list

Use of the channel list

You can configure the channel list by moving, deleting,
renaming and locking them to your liking.

Setting of parental control settings

To prevent certain programs from being watched, channels
and menus can be locked through the parental control system.
To display lock menu option, enter the PIN code. By
default, the set factory code is 0000. After entering the
appropriate PIN code, the Parental control settings
menu will be displayed :
Menu lock : The Menu lock option enables or disables
access to the menu.
Maturity lock: After installation, this option searches
information related to parental programs and if this
parental level has been disabled, access to broadcast
is not enabled.
Parental control lock: When the Parental lock option
is selected, the television can only be controlled with a
remote control. In this case, the control panel buttons
will not be active.
PIN code setting: Defines a new PIN code.
The default PIN code can change depending on
the country selected.
If a PIN code is required to display a menu option,
enter one of the following codes: 0000 or 1234.

Electronic Program Guide (EPG)

Some channels, not all, display information concerning
the on-going program and the next one. Press the
button to get access to the EPG menu.
Up/Down/Left/Right: Navigate EPG.
OK: Displays programme options.
INFO: Displays, in detailed, information on the
programme selected.
GREEN: Switches to List Schedule EPG.
YELLOW: Switches to Timeline Schedule EPG.
BLUE: Displays filtering options.

Programme Options

In EPG menu, press the OK button to enter the
Event Options menu.
Select Channel
In EPG menu, using this option, you can switch
to the selected channel.
Set Timer / Delete Timer
After you have selected a programme in the EPG
menu, press the OK button. Select the Set Timer on
Event option and press the OK button. You can set
a timer for future programmes. To cancel an already
set timer, highlight that programme and press the
OK button. Then select "Delete Timer" option. The
timer will be cancelled.
(RECORDING): The television starts to record
the selected program. You can press again to stop
recording.
More info on the events
P+P-:
IMPORTANT : Connect your USB device only when your
television is turned off. Then turn on the TV set in order to
enable the record function.
Note: During recording,it is not possible to change the
channel or Source.
Note: It is impossible to record two channels at the same time.

Troubleshooting and tips

The TV is not coming on
Check to ensure that the electricity plug is safely
connected to the wall socket or that the batteries of
the remote control are functional.
Poor picture quality
• Check if your antenna is properly connected. A poor
signal level can negatively affect image quality.
• If you carried out manual settings, verify that you
entered the right channel frequency.
• Image quality may be affected negatively when two
devices are connected to the television set at the same
time. If such is the case, disconnect one of the devices.
No image
• No image indicates that your TV is not receiving a
signal. Have you selected the correct buttons on the
remote control? Try once more. Also make sure that
you have selected the right input source.
• Is the antenna connected properly?
• Is the antenna cable damaged?
• Are suitable plugs used to connect the antenna?
• If you are not sure , please consult your supplier.
No sound
• Has the mute button been pressed? If that is the
case, press the "
• Only one speaker is producing sound. Is the balance
well placed in the middle? Consult the Sound menu.
The remote control is not working
• The batteries may be down. Replace the batteries.
Input sources cannot be selected.
• If you cannot select an input source, it is possible
that no device is connected.
• Check the AV cables and connections if you have
tried to connect a device.
Recording not available
To record a programme, you first have to connect your
USB device to your television which you have to shut
down first. Then turn on the TV set in order to enable the
record function. If you are unable to record, try turning
off the television and inserting the USB device again.
English - 37 -
" button, or increase the volume.