Maintenance And Cleaning - COLETTO Sportivo isofix Gebrauchsanleitung

vehicle's seat
b) Rotate the adjuster button in anti-clock wise directional-1),and pull the
isofix anchors outwards as far as it goes, wake sure it can't be push back
(1.2)
c) Push the car seat towards the back of vehicle's seat (2.1)
d) Match the isofix anchors to the vehicle's anchoring point until hear a
"click"(2-2)
e) Rotate the adjuster button in anti-clock wise direction (3.1), and push the
car seat fo the bock of vehicle's seat as much as possible (3.2)
f) Hook the top tether up and pull as tight as possible.
Placing child in the "Coletto Sportivo isofix/Vivaro isofix/Corto isofix"
seat
Loosen the shoulder belts by pressing the release button and pull the
shoulder belts towards you. Important: Do not pull on the belt pads when
doing so. (F8-9)
Press the red button to open the buckle.(F10) Part the belts over the sides of
the shell.(F11) Place your child into the shell and make sure that there are no
toys or other hard objects in the shell.(F12) Match buckle tongue sections
together and insert them into the buckle.(F13) f) Make sure the shoulder belts
fit your child snugly by pulling the adjuster belt. (F14) Note! After you have
done the installation, check it by trying to move it, it shouldn't move more than
an inch at either side, if it does, tighten the straps or try installing it again. The
belts should never be twisted. If you are unable to click the tongue sections
into the buckle, unlock the buckle by pressing the red button and try again.
Installation for group II/III
This installation method is for a child within Group II (15-25kg) and Group III
(22-36kg).
Note: the "Coletto Sportivo isofix/Vivaro isofix/Corto isofix" must be used
Isofix anchors plus top tether at the same time with 3-point automatic seat
belt for group n /H all the time.
a) Remove the harness system, including the belt pads, central buckle and
crotch strap.
b) Adjust the headrest by pulling the lifting handle at your required position
according to your child's height.
c) Place your child into the car seat.
d) Thread the vehicle's shoulder belt from the Group II belt guide slot (F14-a),
or Group III belt guide slot (F14-b),and thread the lap belt into the belt guide
hole (F14-c). So the installation is completed (F14-d).
e) Joint the belts and buckle up.
Adjusting the height of the shoulder belts.
a) The correct height of the shoulder belts is attained when the belt
disappears into the shell slightly above the shoulder of the child. Ensure that
the shoulder belts fit comfortably over the child's shoulder. (F15)
b) Loosen the shoulder belts by pressing the release button of the adjuster
and pulling the shoulder belts towards you as far as possible.
13
Important: Do not pull the belt pads when doing so.(F9)
c) Place the shell of the seat in the sleeping position.
d) Remove the shoulder belts from the yoke.(F16-a).
e) Pull the shoulder belts through the belt pads and belting slots in shell,
ensuring that the buckle remains
twisted.(F17)
f) If you want to alter the belts from or to the lowest positions, adjust the
car seat to the sleeping position.
g) If you want to alter the belts from or to the higher positions, adjust the car
seat to the sitting position.
h) Place the shoulder pads at the expected height and thread the shoulder
straps back through the shoulder pads, cover and shell. (F18)
I) Connect the shoulder belts to the belt yoke. (F19-a)

MAINTENANCE AND CLEANING

General:
a) The car seat can be cleaned by using lukewarm water and soap. Do not
use aggressive cleaners like abrasives or thinners.
b) The cover should be washed by hand at a maximum temperature of
30'C. Do not put it in the dryer.
Step 1. Take the car seat out of your car; ensure your baby's toys are put
away before you begin cleaning it.
Step 2. Remove food particles and dirt with a cordless vacuum cleaner if
possible, use a portable vacuum cleaner's furniture attachment to clean the
small, hard-to-reach areas of the car seat.
Step 3. Clean off the plastic portions of the seat with gentle soap and water.
Step 4. Remove the entire car seat cover, if possible, and run it through
your washing machine using a gentle cycle.
Step 5. Spot clean the stained spots on the car seat if you cannot remove
the cover; make sure you can use the soap on the car seat's material by
checking the package's guidelines.
Step 6. Reinstall the clean car seat in your car, and take special care that all
parts of the car seat being present and installed safely and correctly.
Removing and Replacing the cover and belt pads
a) Loosen the belts pads. (See adjusting the height of the shoulder belts)
b) Loosen the cover all around.(F20)
c) Pull the belts, buckle tongues and buckle through the cover.
d) Remove the cover.
e) After washing, attach the belt pads and place the cover on the shell.
f) Thread the buckle, tongues and belts through the cover and fasten the
cover at the release button/ positioning handle.
g) Secure the cover on the pins.
h) Close the buckle and thread the belts through the belt pads, cover and
shell.
I) Connect the shoulder belts to the belt yoke, j) Fasten the cover all around,
fixed to prevent the belts
14
being