Maintenance; Spare Parts/Accessories - Sundstrom SR 584 Gebrauchsanleitung

EN
Contents
1. General
2. Use
3. Warnings

4. Maintenance

5. Spare parts & Accessories
6. Approvals
1. General
The Sundström SR 584 welding shield is intended for use to-
gether with the Sundström SR 580 Helmet with visor and with
the Sundströms battery-powered fan SR 500/SR 700 or
compressed air attachment SR 507.
The SR 584 in combination with the SR 580 and fan/com-
pressed air is designed specifically for protection against harm-
ful gases, radiation and spatter during welding, flame-cutting,
grinding and similar work. The design of the combination makes
it usable for work in confined and inaccessible areas.
2. Use
2.1 Welding lens
For replacement of welding lens. See 4.4.
2.2 To put on take off the helmet
Follow the directives in the user instructions for the SR 580
helmet.
2.3 To fit the welding shield on the helmet
• Remove knobs and washers from the helmet. Fig. 1.
• Mount the welding shield on the helmet. Fig. 2.
2.4 To remove the welding shield
• Remove the welding shield. Fig. 3. (Replace the washers and
knobs on the helmet.)
3. Warnings
• Change the lens immediately if it is found to be damaged.
• Materials that come into contact with the user's skin may give
rise to allergic reactions if the user is sensitive.
• The outer, hinged holder for protective lens must be fully
lowered while work is in progress.
• If the welding shield is equipped with a toughened mineral
glass lens, a protective lens should be fitted on the inside of
it.
• Damaged or scratched occulars must immediately be re-
placed.
4. Maintenance
Personnel who are responsible for maintenance of the equip-
ment must be trained and thoroughly familiar with this type of
task.
4.1 Cleaning
Clean welding visor and glass with Sundström SR 5226 cleaning
wipes or with a mild soap solution.
4.2 Storage
After cleaning, the equipment should be stored in a dry
and clean location at room temperature.
Avoid direct sunlight. The welding shield is not
affected by an extended period of storage.
8
Welding shield SR 584
4.3 Replacement of protective lens
The lens must be CE marked and of standard 90x110 mm size.
• Remove the old protective lens. Fig. 4, 5, 6.
• Fit a new protective lens. Fig. 7, 8, 9, 10.
4.4 Replacement of welding lens
The lens must be CE marked and of standard 90x110 mm size.
Welding lens
• Remove the old welding lens. Fig. 11, 12, 13, 14.
• Fit a new welding lens in the reverse order. Fig. 14, 13, 12, 11.
Automatic lens
• Remove the old automatic lens. Fig. 15, 16.
• Fit a new automatic lens in the reverse order. Fig. 16, 15.
4.5 Fitting the correction lens
• Place the correction lens on the inside of the welding lens.
5. Spare parts & Accessories
Description
Frame, welding shield
Adapter right+left
Knob complete
Lock device welding lens
Welding lens, shade No. 8, SR 59008
Welding lens, shade No. 9, SR 59009
Welding lens, shade No. 10, SR 59010
Welding lens, shade No. 11, SR 59011
Welding lens, shade No. 12, SR 59012
Welding lens, shade No. 13, SR 59013
Automatic lens. EN 3/10, SR 59005
Automatic lens. EN 3/11, SR 59006
Automatic lens. EN 4/9-13, SR 59007
Inner protective lens for automatic lens
Correction lens, dptr 1,0, SR 59014
Correction lens, dptr 1,5, SR 59015
Correction lens, dptr 2,0, SR 59016
Correction lens, dptr 2,5, SR 59017
Spring for welding lens
Protective lens PC
Holder protective lens
Neck and chest protection
Face seal
Protective hood
Protective hose for the breathing hose
6. Approvals
CE/EN
The SR 584 has been tested and approved in accordance with
EN 175 S and PPE 89/686/EEC. S is increased robustness.
The EC type approval certificate has been issued by Notified
Body 0194. For the address, see back-cover.
American Standards Mark
Provides respiratory protection with an APF of 25 (Assigned
Protection Factor) according to OSHA 3352-02 2009. Provides
limited eye protection (ANSI Z87.1-2010). Provides limited head
protection (ANSI Z89.1-2009 Type 1 Class G).
Ordering No.
R06-0816
R06-0820
R06-0821
R06-0819
T06-4001
T06-4002
T06-4003
T06-4004
T06-4005
T06-4006
T06-4007
T06-4008
T06-4009
R06-4009
T06-4010
T06-4011
T06-4012
T06-4013
R06-0818
R06-4008
R06-0817
T06-8011
T06-8012
T06-4014
T06-4016