Technical Data; Care And Cleaning - BASETech 1691751 Bedienungsanleitung

d) Setting the alarm
• To set the alarm time, press the MODE button (B) twice in time mode. The day of the week
indicator with "MO" starts to flash and the hour setting of the alarm time flashes. Press the
START/STOP button (C) to set the hours in ascending order.
• Press the SPLIT/RESET button (A) to switch to the minutes. The minutes flash. The minutes
can also be set in ascending order in repeating cycle with the START/STOP button (C).
• When the alarm time is set, the alarm is activated automatically (as confirmed by the bell
symbol on the display).
• Press and hold the START/STOP (C) button to run through the digits quickly.
• Pressing the START/STOP (C) confirms and terminates the alarm setting.
e) Alarm functions
Activating/deactivating the alarm setting
• Pressing and holding the SPLIT/RESET (A) button in time mode displays the set alarm time.
Press and hold the SPLIT/RESET button (A) again. You can now press the START/STOP
button (C) to switch the alarm on or off.
• When the alarm is on, a bell symbol is shown on the LC display. It disappears when the alarm
function is switched off. When the alarm function is switched on, the bell symbol is shown
again. There is a confirmation sound on setting.
Activating/deactivating the hourly alarm
• Pressing and holding the SPLIT/RESET button (A) in time mode switches the hourly alarm
on when the MODE button (B) is pressed at the same time.
• If the hourly alarm is on, the entire day of the week bar is shown on the LC display. The alarm
is triggered briefly at every full hour.
• Pressing the MODE button (B) again switches the hourly alarm in double cycle off again. The
day of the week bar disappears when the hourly alarm is switched off.
Switching off an activated alarm
• When the alarm sounds, press the SPLIT/RESET button (A) or START/STOP button (C) to
switch it off.
f) Stopwatch
• Press the MODE button (B) once in time mode to go to the stopwatch display.
• Press the START/STOP button (C) to start the stopwatch. The display shows 1/100 seconds,
1/10 seconds, seconds and minutes.
• Pressing the START/STOP button (C) again stops the stopwatch again. You can read the
result.
• Pressing the SPLIT/RESET button (A) resets the stopwatch to zero. New times can now be
taken.
If you'd like to take split times, e.g. times for two or more runners, you can display one or more
split times in chronological order.
• To do this, start the stopwatch by pressing the START/STOP button (C) to start time
measurement.
• Once the first runner has reached the line, press the SPLIT/RESET button (A) to freeze the
split time of the first runner on the display. The stopwatch continues to run in the background.
• When the second runner reaches the line, press the START/STOP button (C) to stop the
time measurement. The time of the second runner is now shown on the LC display.
• To take further split times, press the SPLIT/RESET button (A) for each further split time
(runner). The values are frozen on the display so that you can read them and note them
down.
• Time measurement is stopped only when the START/STOP button (C) is pressed.
• After stopping the stopwatch, press the SPLIT/RESET button (A) to delete the values. This
deletion works only after a time measurement stopped with the START/STOP button (C). The
stopwatch is reset to zero.

Care and cleaning

• The product is maintenance-free except for battery replacement and occasional cleaning.
• Do not place the product in or under water for cleaning.
• Do not press too strongly on the surface, as this may lead to scratch marks.
• Before cleaning the product, disconnect it from the power supply by removing the battery.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the casing or cause the product to malfunction.
• Use a dry, lint-free cloth to clean the product.
Disposal
a) Product
Electronic devices are recyclable waste and must not be placed in household
waste. At the end of its service life, dispose of the product according to the relevant
statutory regulations.
Remove any inserted battery and dispose of it separately from the product.
b) Batteries
You are required by law to return all used batteries (Battery Directive). They must not
be placed in household waste.
Batteries that contain hazardous substances are labelled with this symbol to indicate
that disposal in domestic waste is forbidden. The abbreviations for heavy metals in
batteries are: Cd = Cadmium, Hg = Mercury, Pb = Lead (indicated on the battery, e.g.
below the waste bin icon on the left).
Used batteries can be returned to collection points in your municipality, our stores or wherever
batteries are sold.
You thus fulfil your statutory obligations and contribute to protection of the environment.

Technical data

Power supply ................................ 1x 1.5 V LR44 button cell
Time format .................................. 12 or 24 hours
Number of lap/split times .............. 1
Accuracy ....................................... 1/100 second
Material ......................................... Plastic
Paint ............................................. Yellow and black
Precision time ............................... To 1/100 second during the first 30 minutes
Dimensions (W x H x D) ............... 55 x 14 x 73 mm
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or capturing in
electronic data processing systems) requires prior written approval from the publisher. Reprinting, also in part, is
prohibited. This publication reflects the technical state at the time of printing.
Copyright 2018 by Conrad Electronic SE. *1691751_v1_0818_02_DS_m_4L_(1)