Care And Maintenance; Warranty Disclaimer; Hands-Free Function - Hama Tour ANC Bedienungsanleitung

Note – Connection impaired
After the headset and terminal device have been paired, a
connection is established automatically. If the Bluetooth
connection is not established automatically, check the
following:
• Check the Bluetooth settings of your terminal device to see
®
whether Hama BTH TOUR ANC is connected. If not, repeat
the steps listed under 5.1. Bluetooth
• Check whether obstacles are impairing the range. If so,
move the devices closer together.
• The performance can also be affected by a weak battery.
5.3. Bluetooth multipoint connection
®
This headset can be connected with two Bluetooth
terminal devices simultaneously.
• First connect the headset with the first terminal device as described in 5.1.
• Then disable Bluetooth on that terminal device.
®
• Next, connect the headset with the second terminal device as
described in 5.1.
• Activate Bluetooth on the first terminal device once more. The
®
headset now connects to that terminal device automatically.
5.4. Audio playback
Note
• Note that the functions described under 5.4. and 5.5. are
only possible with an active Bluetooth
• Your terminal device must also support the individual
functions.
• For more information, please refer to the operating
instructions of your terminal device.
• Functions can still be controlled directly via the terminal device.
• Set the volume on your terminal device to a low level.
• If the connection was successful, a voice says 'Your device is
connected' and the blue LED (5) flashes.
• Start audio playback on the connected terminal device.
• Press Volume + (1) to increase the volume.
• Press Volume - (2) to reduce the volume.
• Press the MFB button (6) to start or pause audio playback.
• Press and hold Volume + (1) to skip to the next title.
• Press and hold Volume - (2) to skip to the previous title.

5.5. Hands-free function

• Press the MFB button (6) once to answer an incoming call.
• Press the MFB button(6) twice or use your telephone to reject an
incoming call.
• During a call, press the MFB button (6) once to end the call.
4
®
pairing.
®
-enabled
®
connection.
®
Note – Call quality
To increase the call quality, make sure that you are near the
headset with your mobile phone during the call.
5.6. ANC function
This headset comes with a noise cancelling function (ANC) to
reduce unwanted ambient noise (for example, the noise of an
air-conditioning system). To switch on the function, press and
hold the ANC button (4) until the LED (3) lights up. To switch this
function off again, press the ANC button (4) once more. The LED
(4) goes out.
5.7. Audio input socket
In addition to connecting this headset via Bluetooth
connect it using the included AUX cable.
To do so, insert one end of the cable into the terminal device and
the other end into the Audio input socket (6) on the left side of
your headset. The Bluetooth
when you plug in the audio cable. The headset now functions as
a wired headset.
5.8. Disconnecting the headset
• Switch the headset off.
• Disconnect the headset via the Bluetooth
terminal device.

6. Care and Maintenance

Only clean this product with a slightly damp, lint-free cloth and do
not use aggressive cleaning agents. Make sure that water does not
get into the product.

7. Warranty Disclaimer

Hama GmbH & Co KG assumes no liability and provides no
warranty for damage resulting from improper installation/mounting,
improper use of the product or from failure to observe the operating
instructions and/or safety notes.
8. Service and Support
Please contact Hama Product Consulting if you have any questions
about this product.
Hotline: +49 9091 502-115 (German/English)
Further support information can be found here:
www.hama.com
, you can
®
connection is automatically ended
®
settings on your
®