Maintenance - Chicago Pneumatic CP3030-325AFR Betriebsanleitung

EN
English
INSTRUCTION MANUAL
Machine Type:
Pneumatic tool equipped with a flexible disc fitted
with abrasive paper for sanding - No other use is
permitted.
Air Supply Requirements
1. Supply tool with 90 psig (6.3 bar) of clean, dry air.
Higher pressure drastically reduces tool life.
2. Connect tool to air line using pipe, hose and fitting
sizes shown in the diagram below.
3. Do not install a quick coupler directly into the
sander throttle handle.
3/8" (10mm)
Lubrication
Use an air line lubricator with SAE #10 oil, adjusted
to two drops per minute. If an air line lubricator
cannot be used, add air motor oil to the inlet once a
day.

Maintenance

1. Disassemble and inspect tool every three months
if the tool is used every day. Replace damaged or
worn parts.
2. High wear parts are underlined in the parts list.
Technical Data
Disc
diameter
in. - mm
CP3030-325AFR 2 - 50
CP3030-415AFR 3 – 75
CP3030-420AFR 3 - 75
CP3030-515AFR 3 - 75
Air pressure 90 psi (6.3 bar)
Original Instructions
Copyright 2012, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the
contents or part thereof is prohibited. This applies in particular to
trademarks, model denominations, part numbers and drawings.
Use only authorized parts. Any damage or malfunction caused
by the use of unauthorized parts is not covered by Warranty or
Product Liability.
1/2" (12mm)
CA048362 (1/2")
90
0 130
1/2" (12mm)
CA048360 (1/2")
CA048361 (1/2")
Spindle Free Speed Air Cons.
thread
RPM
1/4"-20 25000
3/8" - 24 15000
3/8" - 24 20000
3/8" - 24 15000
Noise & Vibration Declaration*
CP3030-325AFR
CP3030-415AFR
CP3030-420AFR
CP3030-515AFR
*re. ISO 28927-3
**uncertainty 3 dB(A), in accordance with
EN ISO 15744. For sound power, add 11 dB(A).
Declaration of noise and vibration emission
All values are current as of the date of this publication. For the
latest information please visit cp.com.
These declared values were obtained by laboratory type
testing in accordance with the stated standards and are
suitable for comparison with the declared values of other
tools tested in accordance with the same standards. These
declared values are not adequate for use in risk assessments
and values measured in individual work places may be higher.
The actual exposure values and risk of harm experienced by
an individual user are unique and depend upon the way the
user works, the workpiece and the workstation design, as well
upon the exposure time and the physical condition of the user.
We, Chicago Pneumatic, cannot be held liable for the
consequences of using the declared values, instead of
values reflecting the actual exposure, in an individual risk
assessment in a work place situation over which we have no
control.
This tool may cause hand-arm vibration syndrome if its
use is not adequately managed. An EU guide to managing
hand-arm vibration can be found at www.pneurop.eu/uploads/
documents/pdf/PN3-02-NV_Declaration_info_sheet_0111.pdf
We recommend a programme of health surveillance to
detect early symptoms which may relate to noise or vibration
exposure, so that management procedures can be modified to
help prevent future impairment.
cfm - l/s
22 -10,3
22 -10,3
27 -12,8
25 -11,8
CP3030 AFR Series
Vibration* Sound pressure level**
(m/s²)
<2,5 80
<2,5 80
<2,5 76
<2,5 76
Sander
(dBa)