Electrical Safety - Husqvarna TS 230 F Betriebs- Und Wartungsanleitung

This symbol indicates that the
machine is in conformance with
the applicable European directive.
MANDATORY
WARNING
These signs give advice
concerning your safety
Instruction plate
MANUFACTURER
TYPE TYPE
FABRICATION
WEIGHT MASSE UTILE Kg
MAXI TOOL Ø MAXI OUTIL. mm
BORE Ø ALESAGE mm FREQUENCE
SPEED T/MN - RPM
1 Utilisation
• Utilisation : Water-cooled cutting of tile
materials.
• Blade with continuous rim Ø 230 mm (D)
bore Øx25.4 mm (AL).
Use only continuous rim diamand
blades.
• Cutting thickness (material) :
to 90° : 48 mm - to 45° : 37 mm
• Cutting width (Lg) with guide at 90° :
305 mm to the left
147 mm to the right
• Length of cut unlimited.
2 Technical features
• Power : 0,75 Kw (1 CV)
• Voltage : 230 V - 50 Hz
• Motor speed : 2800 rpm
• Dimensions (mm) l x w x h :
- 660 x 520 x 325
• Weight : 18 kg
• Blade cooling by partial immersion
• Tank capacity: 1,5 litres (autonomy 40 minu-
tes cutting)
• Power cable : HO5 VVF 3 x 0.75 mm
1,50 m.
POWER
MODEL
LEVEL
Lwa (dB)
ISO 3744
0.75 KW 240 V 76
0.75 KW 115 V 74
7
3
INDICATION
INFORMATION
INSTRUCTION
PROHIBITION
N° SERIE SERIAL
FABRICATION
ANNEE DE
YEAR
PUISSANCE kW POWER
PLAGE DE
V VOLTAGE
TENSION
Hz FREQUENCY
INT. UTIL. A INTENSITY
4
115 V - 50 Hz
2
- length
PRESSURE VIBRATION
LEVEL LEVEL
Lpa (dB) G en NF
ISO 4871 ENV 25349
63 0.09
65 0.07
Pre-use check-list
Before use, read the instructions
carefully and familiarise yourself
with the machine.
The working area must be per-
fectly tidy, well lit and must offer
no risks (no humidity or dange-
rous products in the vicinity).
The operator must wear
suitable protection when
working.
Any unauthorised persons must
be kept away from the working
area.
Use blades suitable for the work
to be done (speed, geometry,
application, etc.)
Electrical connections

- ELECTRICAL SAFETY :

Operate this machine only on a
supply equipped with a 30 mA ear-
thed current-limiting circuit-brea-
ker. Otherwise, consult our catalo-
gue for appropriate models.
- The RCCB must be used cor-
rectly, including testing it regu-
larly. For tools supplied with an
integral RCCB in the cable or in
the mains plug, if the cable or
plug has been damaged,
repairs must be carried out by
the manufacturer, one of his
agents or by a qualified repair
workshop to avoid any risks
resulting from errors.
- Check the mains voltage is iden-
tical to that shown on the instruc-
tion plate N on the machine
[FIG.x1]
- Use twin & earth plugs S.T.D. 3
pin plug 240 V.
- Extension cable : cable section
adequate for the electric power,
connection to the main by a type
HO7 RNF cable of 2.5 mm
tion up to 50 m.
5 Fitting the blade
• Unplug the machine.
• Remove the housing from the disk (fig 1).
• Remove the table by pulling on the levers
(figs. 2 and 3).
• Remove the motor clamp screw, right-
hand thread.
• Remove the pressure disk.
• Offer up the diamond cutting blade.
Rotation direction is indicated by
an arrow on one side of the
blade.
Make sure the contact faces of
flanges, of blade and the axle are
clean
• Check correct centring of the blade.
• Replace the outer flange and lock the nut.
• Replace the table
• Replace the disk housing
6 Starting up
Always take care.
Get into a comfortable, balanced
position.
Remove all adjustment tools and
wrenches from floor and machi-
ne
Keep the protective covers in
place while the machine is opera-
ting.
• Fill the water bath.
• Connect the machine to the mains.
• Start by means of the on-off switch
2 sec-
I
.
11