Herunterladen Inhalt Inhalt Diese Seite drucken

Hitachi VTMX900ECT Wartungshandbuch Seite 34

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

2-28
5.3 Adjustment of the audio linear playback
amplitude [IIC-bus]:
Purpose: To set audio part amplification LA71595 [7004-A]
Symptom, if incorrectly set:
Playback sounds too low or too loud.
– Enter the service test program and, whilst step display is
flashing, enter the step number 62, using the numerical keys.
TP
ADJ.
MODE
SP Self-recording
Pin 1 of
and Playback,
refer to
Scart 1
Service mode
description
(Audout)
call up Step 62
TAPE
MEAS. EQ.
AC Millivoltmeter,
Blank
Video Pattern,
Tape
Frequency
Generator
By pressing the SELECT button whilst step 62 is flashing, the output
select is switched to Mono and the display shows, for instance:
– Make a recording of the audio signal on E1.
– Connect the millivoltmeter to Scart1 Pin1(Audio out) and play
the recording back.
– The level on Scart 1, Pin1 (Audio out) can be adjusted to the set
value by pressing the UP (value increases) or DOWN keys
(value decreases).
(The amplitude changes by 1 dB each time the key is pressed).
The range is shown in the display by the numbers 0...31.
– The value is automatically stored in the EE-PROM
each time the button is pressed.
6. Display Control (AIO2)
Service tasks after replacement of the clock quartz [1170] or the
EEPROM:
6.1 Clock frequency output
Purpose: Setting the exact clock function.
Symptom, if incorrectly set:
The clock is too fast or too slow.
Remove the Motherboard from the frame and bring it into the service
position.
Enter the service test program and, whilst step display is flashing,
enter the step number 99, using the numerical keys.
TP
ADJ.
MODE
7899-A
pin 71
Service Mode
call up Step 99
CLOCK ADJ.
TAPE
MEAS. EQ.
Frequency counter
with 6 digits
After entering with SELECT, the display is switched off and the
watch symbol is flashing, no further function can be carried out. At
the CLOCK ADJUST measuring point [7899-A, pin 71], the
uncorrected clock frequency of approx. 8192 Hz is always output.
GB
INPUT
(Video white picture)
Audio in Scart 1,
700mV
1kHz
RMS,
SPEC.
500mV
RMS
±50mV
INPUT
Stop
SPEC.
refer to description
below
Determining the correction value for Step 53:
Correction value = Deviation / 0.763 + 128 (round off to whole
number)
The calculated correction value must be between 0 and 255
(change quartz otherwise), and must be entered in Step 53 and
saved.
This step can either be exited by performing a main power source
reset, after which the service program must be entered again or by
pressing any key on the set, before step 53 can be entered.
Example:
f
=8191.97Hz
f
=8192.00Hz
mess
nom
6
Deviation = 1x10
x (8191.97 - 8192.00) / 8192.00 = -3.662
Correction value = -3.662 / 0.763 + 128 = 123.20 = 123
6.2 Inputting the clock correction
By pressing the SELECT key whilst step 53 is flashing, the display
shows, for instance (128 is the default value of an empty EEPROM):
Using the numerical keys of the remote control, the established
correction value from Step 99 is entered as a 3-digit number (value
must be between 0 and 255).
After pressing the OK key on the remote control, the entered code is
stored, the display shows OK for approx. 3 seconds and then the
stored value in decimal format.
In case of an invalid entry (value >255), the activation of the OK key
causes the content of the last stored value to be displayed and OK
does not appear in the display.
To leave the step press Select.

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis