Tuning Terrestrial Television Channels (Dvb-T); Tuning Television Channels From The Cable Provider (Dvb-C) - Grundig 26 VLE 8200 SL Bedienungsanleitung

SETTINGS
-----------------------------------------------------------------------------------------------------------------------------------------
Tuning terrestrial television
channels (DVB-T)
1
In the »Source Setup« menu, in the »Connec-
tion Type« line, select the option »Air« with
< >
» « or » «.
2 Select the line »Scan Type« with »
» «.
Λ
< >
Use » « or » « to set the required scan
type:
– »DTV«, scan for digital television channels;
– »ATV«, scan for analogue television
channels;
– »ATV & DTV«, scan for analogue and
digital television channels.
Caution:
The antenna power supply (5V
7
be switched on if the antenna is an active
indoor antenna with a signal amplifier and it
is not already supplied with a voltage via a
mains plug (or similar supply). Otherwise
you may cause a short circuit and irrepara-
bly damage your antenna.
3
Select the line »Active Antenna Power« with
» « or » «.
V Λ
Switch on the antenna power supply for the
<
antenna with » « or »
4
Start the scan with » « (green).
– The »Search Results« menu appears, and
the search for TV channels begins.
– Depending on the number of television
channels received, this can easily take a
few minutes.
– The scan is complete as soon as the »PRO-
GRAM TABLE« appears.
Note:
You can abort the scan by pressing
7
»MENU«.
5
Press »MENU« to end the setting.
Note:
Before recording HD channels, please
7
check signal quality and Strength, see
chapter "Displaying signal information" on
page 76. If the level is displayed in green,
you can record HD channels without any
problems.
« or
V
) may only
>
« (»On«).
Tuning television channels from
the cable provider (DVB-C)
1 In the »Source Setup« menu, in the »Connec-
tion Type« line, select the option »Cable«
< >
with » « or » «.
2 Select the line »Scan Type« with »
< >
Use » « or » « to set the required scan type:
– »DTV«, scan for digital television channels;
– »ATV«, scan for analogue television channels;
– »ATV & DTV«, scan for analogue and
digital television channels.
3
Select the line »Cabel Scan Type« with »
or » «. Select the preferred option (»Quick«
Λ
<
or »Full«) with » « or »
– The search function »Quick« sets up the
channels according to the information pro-
vided by your cable provider in the trans-
mission signal.
– If the option »Full« is selected, the entire
frequency range will be scanned. The
search can take a long time with this op-
tion. This option is recommended if your
cable provider does not support the scan
type »Quick«.
Note:
You can accelerate the search. To do this,
7
you need information about the frequency
and network ID. You are usually able to get
this data from your cable operator or find it
in forums on the Internet.
4
Start the scan with » « (green).
– The »Search Results« menu appears, and
the search for TV channels begins.
– Depending on the number of television
channels received, this can easily take a
few minutes.
– The scan is complete as soon as the »PRO-
GRAM TABLE« appears.
Note:
You can abort the scan by pressing
7
»MENU«.
5 Press »MENU« to end the setting.
Note:
Before recording HD channels, please check
7
signal quality and Strength, see chapter
"Displaying signal information" on page 76.
If the level is displayed in green, you can
record HD channels without any problems.
« or » «.
V Λ
«
V
>
«.
17
ENGLISH