Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
SETTINGS
-----------------------------------------------------------------------------------------------------------------------------------------
Tuning terrestrial television
channels (DVB-T)
»
1
In the
Source Setup
«
tion Type
line, select the option
»
«
»
«
B
A
or
.
»
2
Select the line
»D«
.
»
«
»
«
Use
or
to set the required scan type:
B
A
»
«
–
DTV
, scan for digital television channels;
»
«
–
ATV
, scan for analogue television
channels;
»
«
–
ATV & DTV
digital television channels.
Caution:
The antenna power supply (5V
7
be switched on if the antenna is an active
indoor antenna with a signal amplifier and it
is not already supplied with a voltage via a
mains plug (or similar supply). Otherwise
you may cause a short circuit and irrepara-
bly damage your antenna.
3
Select the line
»C«
»D«
with
or
Switch on the antenna power supply for the
»
B
«
antenna with
4
Start the scan with
»
– The
Search Results
the search for TV channels begins.
– Depending on the number of television
channels received, this can easily take a
few minutes.
– The scan is complete as soon as the
«
GRAM TABLE
appears.
»M«
5
Press
to end the setting.
«
»
menu, in the
Connec-
»
«
Air
«
»C«
Scan Type
with
, scan for analogue and
) may only
»
Active Antenna Power
.
»
A
«
»
«
or
(
On
).
» «
(green).
«
menu appears, and
»
Tuning television channels from
the cable provider (DVB-C)
»
1
In the
Source Setup
tion Type
with
»
«
B
with
2
Select the line
or
»D«
.
»
«
Use
B
»
«
–
DTV
»
«
–
ATV
channels;
»
–
ATV & DTV
digital television channels.
3
Select the line
»C«
or
»
«
(
Quick
– The search function
channels according to the information pro-
vided by your cable provider in the trans-
mission signal.
– If the option
frequency range will be scanned. The
«
search can take a long time with this op-
tion. This option is recommended if your
cable provider does not support the scan
»
type
Quick
Note:
You can accelerate the search. To do this,
7
you need information about the frequency
and network ID. You are usually able to get
this data from your cable operator or find it
in forums on the Internet.
PRO-
4
Start the scan with
»
– The
Search Results
the search for TV channels begins.
– Depending on the number of television
channels received, this can easily take a
few minutes.
– The scan is complete as soon as the
GRAM TABLE
»M«
5
Press
«
menu, in the
«
line, select the option
»
«
A
or
.
»
«
Scan Type
»
«
or
to set the required scan type:
A
, scan for digital television channels;
, scan for analogue television
«
, scan for analogue and
»
Cabel Scan Type
»D«
. Select the preferred option
»
«
»
«
B
or
Full
) with
or
»
Quick
»
«
Full
is selected, the entire
«
.
» «
(green).
«
menu appears, and
«
appears.
to end the setting.
ENGLISH
»
Connec-
»
«
Cable
»C«
with
or
«
with
»
«
A
.
«
sets up the
»
PRO-
17
Quicklinks ausblenden:
Werbung
Kapitel
Inhaltsverzeichnis
Fehlerbehebung
