Störungen - Oase Atlantis 30 Gebrauchsanweisung

D
Reinigen des Motor- und Pumpengehäuses (C).
Netzstecker ziehen, Auslaufschlauch entfernen, Gehäuseverschluss drücken und Pumpenfilter aufklappen. Pumpe
herausnehmen und Pumpengehäuse abschrauben, alle Einzelteile mit einer weichen Bürste unter fließendem Wasser
säubern, Dichtungsring überprüfen und ggfs. ersetzen.
Achtung! Niemals das Motorgehäuse öffnen! Falls der Rotor ersetzt werden muss oder der Motor defekt ist,
wenden Sie sich zu Ihrer eigenen Sicherheit an einen Elektrofachmann!
Lagern/Überwintern
Bei Frost muss das Gerät deinstalliert werden. Führen Sie eine gründliche Reinigung durch, prüfen Sie das Gerät auf
Beschädigung und bewahren dieses getaucht oder befüllt und frostfrei auf. Der Stecker darf nicht überflutet werden!
Entsorgung
Das Gerät ist gemäß den nationalen gesetzlichen Bestimmungen zu entsorgen. Fragen Sie Ihren Fachhändler.
Störungen
Störung
Gerät läuft nicht
Wasserlauf ungenügend
Gerät schaltet nach
kurzer Laufzeit ab
GB
Information about this operating manual
Please read the operating instructions and familiarise yourself with the unit prior to using it for the first time. Adhere to the
safety information for the correct and safe use of the unit.
Intended use
The Atlantis 30 - 130 series, in the following text termed unit, has been exclusively produced for pumping normal pond
water for filters, water falls and water courses and has to be used at a water temperature of between 4°C and +35°C and
an operating voltage of 230 Volt.
Use other than that intended
Danger to persons can emanate from this unit if it is not used in accordance with the intended use and in the case of
misuse. If used for purposes other than that intended, our warranty and operating permit will become null and void
CE Manufacturer's Declaration
We declare conformity in the sense of the EC directive, EMC directive (89/336/EEC) as well as the low voltage directive
(73/23/EEC). The following harmonised standards apply: EN 60335-1, EN 60335-2-41, EN 55014-2,
EN 61000-3-2, EN 61000-3-3
Safety information
OASE has manufactured this unit according to the highest quality standards and the valid safety regulations. In spite of
the above, hazards for persons and assets can emanate from this unit if it is used in an improper manner or not in
accordance with its intended use, or if the safety instructions are ignored.
For safety reasons, children and young persons under 16 years of age as well as persons who cannot recognise
possible danger or who are not familiar with these operating instructions, are not permitted to use the unit!
Please keep these operating instructions in a safe place! Also hand over the operating instructions when passing the unit
on to a new owner. Ensure that all work with this unit is only carried out in accordance with these instructions.
The combination of water and electricity can lead to danger to life and limb, if the unit is incorrectly connected and
misused. Only operate the unit if no persons are in the water! Prior to reaching into the water, always disconnect the
power supply of all units used in the water.
Compare the electrical values of the power supply with those on the type plate on the packaging or on the unit itself.
Ensure that the unit is fused for a rated residual current of max. 30 mA via a residual current-operating system. Only
operate the unit when plugged into a correctly fitted socket. Keep the power plug and all connection points dry! Protect
the connection cable when burying to avoid damage. Only use cables, equipment, adapters, extension or connection
cables with an earthed contact and approved for outside use. Do not carry or pull the unit by the connection cable! Never
operate the unit if the cable or housing are defective! If the power connection cable of the unit is damaged, have it repaired
by the manufacturer in order to avoid hazards. Electrical installations in garden ponds must meet the international and
national regulations valid for installers. Never open the unit housing or its attendant components, unless this is explicitly
mentioned in the operating instructions. Never carry out technical changes to the unit. Only use original spare parts and
accessories. Only allow authorised customer service outlets to perform repairs. Never run the unit without water! Never
use the pump for fluids other than water! In the event of questions and problems, contact a qualified electrician for your
own safety!
6
Ursache
- Netzspannung fehlt
- Rotor blockiert
- Mengenregulierventil zu weit zugedreht
- Filter verschmutzt
- Schlauch verstopft
- Schlauch geknickt
- Zu hohe Verluste in den Schlauchleitungen
- Filter verstopft
- Wassertemperatur zu hoch
Abhilfe
- Netzspannung überprüfen
- Reinigen
- Mengenregulierventil einstellen
- Filter reinigen
- Reinigen, evtl. ersetzen
- Schlauch prüfen, evtl. ersetzen
- Schlauchlänge auf nötiges Minimum reduzieren
- Reinigen
- Maximale Wassertemperatur von +35°C beachten
Signature: