Herunterladen Inhalt Inhalt Diese Seite drucken

Start-Up; Charging The Rechargeable Battery; Operation; Extending/Shortening The Telescopic Pole (03) - AL-KO HTA 2050 Betriebsanleitung

Akku-hochheckenschere
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1

Start-up

4. Carry out a number of work movements with
the appliance switched off to test the length
of the carrying belt. Adjust the length of the
carrying belt if necessary.
8 START-UP
8.1

Charging the rechargeable battery

CAUTION!
Danger of fire during charging!
Due to heating of the charger, there is a
danger of fire if it is placed on an inflam-
mable surface and is not adequately ven-
tilated.
Always use the charger on a non-in-
flammable surface or in a non-com-
bustible environment.
If available: Keep the ventilation slots
free.
NOTE
Fully charge the rechargeable battery be-
fore using it for the first time. The re-
chargeable battery can be charged in any
charge status. Interrupting charging does
not damage the rechargeable battery.
NOTE
When charging, the rechargeable battery
is protected from overcharging due to au-
tomatic detection of the charge status
and thus can remain connected to the
charging unit for some time, but not per-
manently.
Observe the temperature range for the charging
mode, the charging time until fully charged and
the rechargeable battery operating time, see
technical details. If the operating time of the re-
chargeable battery shortens considerably despite
being fully charged, it has reached the end of its
useful life and must be replaced by a new original
rechargeable battery.
1. Connect the charger (01/8) without the re-
chargeable battery (01/7) to the power sup-
ply. The LED on the plug-in power supply is
green.
2. Insert the rechargeable battery into the char-
ger.
The LED on the plug-in power supply is
red. The charging process begins.
442212_a
Charging is completed when the LED on
the plug-in power supply is green. The
rechargeable battery is then fully
charged.
3. Disconnect the charger from the mains.
4. Remove the rechargeable battery from the
charger.

9 OPERATION

WARNING!
Risk of injury due to detaching appli-
ance parts
Appliance parts detaching during opera-
tion can lead to serious injury.
Before turning the appliance on,
check that all the parts of the appli-
ance are firmly tightened.
Attach cutting tools so that they can-
not detach during operation.
9.1
Extending/shortening the telescopic
pole (03)
The telescopic pole is infinitely adjustable. This
means the length can be adjusted as required for
the work.
1. Unscrew (03/a) the clamping screw (03/1) in
the direction of the arrow until the clamp is
released.
2. Set the required length by moving in the di-
rection (03/c) or (03/d).
3. Screw the clamping screw (03/1) tight in the
direction of the arrow (03/b).
9.2

Turning the cutter head (04, 05)

The cutter head can be adjusted stepwise be-
tween -30°, 0°, +30°, +60° and +90° (05). This
means it can be adjusted as required for the
work.
WARNING!
Danger of cutting injuries
Danger of cutting injuries when reaching
into the cutting blade.
Always switch off the appliance be-
fore turning the cutter head.
1. Switch off the appliance and pull out the re-
chargeable battery.
2. Press and hold the unlock button (04/1).
3. Turn the cutter head (04/2) until it engages in
the required position.
33

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis