Specifications; Safety Instructions - Makita 1806B Betriebsanleitung

ENGLISH
1 Hex wrench
2 Bolt
3 Adjusting screw
4 Planer blade
5 Notch in the blade
6 Drum cover
7 Drum
8 Triangular rule
9 Screwdriver

SPECIFICATIONS

Model
Planing width ...................................................... 170 mm
Planing depth .......................................................... 2 mm
–1
No load speed (min ) .......................................... 15,000
Overall length ..................................................... 529 mm
Net weight .............................................................. 8.8 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.42 Ohms it can be presumed that
there will be no negative effects.
The mains socket used for this device must be protected
with a fuse or protective circuit breaker having slow trip-
ping characteristics.

SAFETY INSTRUCTIONS

Warning! When using electric tools, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury,
including the following. Read all these instruc-
tions before attempting to operate this product
and save these instructions.
For safe operation:
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Don't expose power tools to rain. Don't use
power tools in damp or wet locations. Keep work
area well lit. Don't use power tools in presence of
flammable liquids or gases.
Explanation of general view
10 Knob
11 Switch trigger
12 Lock button
13 Lock-off button
14 Start
15 End
16 Sharpening holder
17 Wing nut
18 Blade (A)
3.
1806B
4.
5.
6.
7.
8.
9.
10. Connect dust extraction equipment
11. Don't abuse cord
12. Secure work
13. Don't overreach
14. Maintain tools with care
19 Blade (B)
20 Side (C)
21 Side (D)
22 Nozzle
23 Makita vacuum cleaner
24 Limit mark
25 Chip cover
26 Brush holder cap
Guard against electric shock
Prevent body contact with grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
Keep children away
Do not let visitors contact tool or extension cord.
All visitors should be kept away from work area.
Store idle tools
When not in use, tools should be stored in dry,
high, or locked-up place, out of the reach of chil-
dren.
Don't force tool
It will do the job better and safer at the rate for
which it was intended.
Use right tool
Don't force small tools or attachments to do the
job of a heavy duty tool. Don't use tools for pur-
poses not intended; for example, don't use circu-
lar saw for cutting tree limbs or logs.
Dress properly
Do not wear loose clothing or jewelry. They can
be caught in moving parts. Rubber gloves and
non-skid footwear are recommendemd when
working outdoors. Wear protective hair covering
to contain long hair.
Use safety glasses and hearing protection
Also use face or dust mask if cutting operation is
dusty.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used.
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and
sharp edges.
Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to oper-
ate tool.
Keep proper footing and balance at all times.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating
and changing accessories. Inspect tool cords
periodically and, if damaged, have repaired by
authorized service facility. Inspect extension
cords periodically and replace if damaged. Keep
handles dry, clean and free from oil and grease.
5