Declaration Of Conformity; Warranty; Troubleshooting - indexa DF25A Set Bedienungsanleitung

17. Declaration of conformity

Indexa GmbH , Paul-Böhringer-Str. 3, D- 74229 Oedheim declares that this
product DF25A Set complies with the basic requirements and the other
relevant regulations of Directive 1999/5/EC. Conformity has been
demonstrated. The complete declaration of conformity can be read at:
www.indexa.de
This product can be used in the following countries:
D A L CH

18. Warranty

In addition to the statutory guarantee from the vendor, the manufacturer
warrants this product for 2 years from date of purchase (proof from receipt)
according to following conditions.This warranty does not affect your legal
rights.
The warranty covers use of the product in normal conditions in private
households. It only covers manufacturing defects and is limited to the
replacement or repair of the faulty components. It does not include wear and
tear, or batteries.
19. Trouble shooting
Fault
Message"NO SIGNAL"
Unstable wireless reception
Monitor picture switches of automatically
In scan mode certain camera signals are not shown
Flickering picture
Picture is too bright
recording not possible
NL B IRL GB
Cause
Incorrect channel selected
Camera not powered
The camera and monitor are not paired
The camera is out of range
Objects are preventing wireless connection
Antenne not firmly attatched or both are not parallel to each
other
Camera channel not activated
Monitor and camera too far apart
Antennas not parallel
Wireless connection is blocked
Interference with wireless signal
Battery is discharged
Power safe mode is selected
Camera channel has not been selected or have no connection
Strong lightsource shining into the camera lens
Overexposure due to strong light source
SD-card not inserted
SD-card locked
SD-card full
The warranty applies only when the product is used according to the
operating instructions. It does not cover damage arising from misuse,
improper handling, application of force, dust, dirt, water or other
environmental factors, or from incorrect voltage from batteries or power
supply.
The warranty is void when the product has been repaired or tampered by
unauthorised persons and when it has been used with components which
are not specified by the manufacturer.
In case of a warranty claim please contact the vendor for details of how to
proceed and how to return the product if necessary. Only carriage paid
authorised returns will be accepted. Repairs can only be accepted when
accompanied by a full description of the fault. After the warranty period has
expired repairs will be charged and are not always possible. Warranty claims
do not extend the warranty period and the warranty for replacement parts
expires with the warranty for the product.
Unless there is a statutory obligation, the manufacturer is not responsible for
further claims, including peronal or material damages, arising from the use
of the product or from nonfunction or misfunction of the product.
Remedy
Select correct channel by pressing button [12]
Check that the Power LED [20] on the corresponding camera lights. If
not, check the mains adapter and cable connection.
Pair camera and monitor
Use an antenna extension cable (see chapter 15)
Reduce the distance between camera and receiver
Remove large objects or change the location of camera and/or receiver
Connect the antenna [33] tightly and position both antennas parallel to
each other, eg. both vertical
Activate the desired camera channel (see Chapter 12.2)
Reduce the distance between camera and monitor
Position of antennas parallel to each other
Remove objects, in particular metallic objects and/or change the location
of camera and/or monitor
Check that there are no interference sources near camera and receiver eg
WLAN Router, elektrical produvts, Microwave ovens
Connect mains adapter
Press any button or turn off the Power safe mode (s. section 12.4)
Refer to chapter 12.5
Move the camera to another location
Change the direction or location of the camera
insert an unlocked, formatted SD-card
unlock the SD-card
format the SD-card (see chapter 12.9)
Indexa GmbH, Paul-Böhringer-Str. 3, 74229 Oedheim, Germany,
www.pentatech.de
GB - 25