BESAFE iZi Modular i-Size base Gebrauchsanweisung Seite 2

9 12
1
10 13
2 3
1
15
11
16 click! click!
click!
14
17
click! rrrt!
19
8
Thank you for choosing BeSafe iZi Modular i-Size base
! It is important that you read this user manual BEFORE
installing your seat. Incorrect installation could endanger
your child.
! Vital information
• The child seat MUST NOT be installed in a front
passenger seat WITH AN ACTIVATED AIRBAG.
• iZi Modular i-Size base can only be installed in a car
equipped with ISOfix anchorage points.
• For the suitable positions in the car, read the vehicle handbook.
• Read the car list to find out whether your car model is approved
for this seat.
• iZi Modular i-Size base can be used in combination with iZi Go
Modular for stature height 40 - 75 cm, and iZi Modular for stature
height 61 - 105 cm.
• The floor support must always be used. Make sure that the floor
support is fully pushed down until it touches the floor of the
vehicle in front of the seat and that the indicators on the floor
support are always showing green.
• DO NOT attempt to dismantle, modify or add any part to the seat.
18
Warranty will be void if non-original parts or accessories are used.
• Do not use any aggressive cleaning products; these may harm the
construction material of the seat.
• BeSafe advises that child seats should not be bought or sold
second-hand.
• KEEP this user manual for later use with the seat.
• DO NOT use the seat for longer than 7 years. Due to ageing, the
quality of the material may change.
• If in doubt, consult either the car seat manufacturer or the retailer.
20
9
Preparing to install
• Front brace (1a)
• Front brace box (1b)
• Floor support (1c)
• Floor support height indicator (1d)
• Height adjuster floor support (1e)
• Seat release handle (1f)
• ISOfix release switch (2g)
• ISOfix indicators (2x) (2h)
• Switch for ISOfix connectors (2x) (2i)
• ISOfix car anchorage (2x) (3j)
• ISOfix insertion clips (2x) (under side) (4k)
• ISOfix connectors (2x) (4l)
Installation of the iZi Modular i-Size base
• The frontbrace is not delivered pre-installed in the base. The iZi Go
Modular can be used on a base without the front brace.
! Warning: When used in combination with the iZi Modular, the front
brace must be installed on the base. Install the front brace in the
two openings, after pulling out the front brace box. The frontbrace
is delivered only with iZi Modular (and available as accessory in case
you want to use a second base for iZi Modular). (5,6,7)
1. When you want to enlarge the available leg room for the child in the
car, you can pull out the front brace box before installation. Use this
possibility only when the iZi Modular seat is in rearfacing position
and when the seat is supported by a vehicle seat or dashboard in
front of the car seat. (8)
2. The frontbrace has to remain on the base once it is installed. The
iZi Go Modular can also be used on a base with the front brace
installed. (9) When used in combination with iZi Go, the frontbrace
has to be in position 1. (10)
3. Only disconnect the front brace when you want to transport the
base flat. To disconnect the front brace, you have to pull the front
brace upwards, while you push with a tool in the hole at the side of
the front brace box. This should be done first on one side and then
the other side.
4. When installing in the back seat of the vehicle, push the front seat of
the vehicle forward as far as possible. (11)