Peg Perego Ypsi Chassis Gebrauchsanleitung Seite 12

body or seat unit or car seat
attachment devices are correctly
engaged before use.
_ WARNING! To avoid injury ensure
that the child is kept away when
unfolding and folding this product.
_ WARNING! Do not let the child play
with this product. This product is
not a toy.
_ WARNING! The assembly and
preparation of the product must be
carried out by an adult.
_ Do not use this product if there are
parts missing or signs of breakage.
_ WARNING! Never leave the child
unattended.
_ Always apply the brake when
stationary and when loading or
unloading children.
_ Do not insert fingers into the
mechanisms.
_ Be careful not to hurt the child
when adjusting the mechanisms
(handlebar, backrest ... ).
_ Any weights hanging on the
handlebar or handles could make
the item unstable; follow the
manufacturer's instructions regards
the maximum loads transportable.
_ Do not load the baskets over 7
Kg. Do not put weight in the cup
holder (if present) in excess of
those indicated on the cup holders
themselves and never hot drinks. Do
not put loads of more than 0.2 Kg in
the hood pockets (if present).
_ Do not use the product near to
stairs or steps, heat sources, naked
flames or dangerous objects within
reach of the child.
_ Only replacement parts supplied or
recommended by the manufacturer/
distributor shall be used.
_ WARNING! This product is not
suitable for running or skating.
_ WARNING! Do not add any
mattress are not approved by the
manufacturer.
_ Do not use accessories which are
not approved by the manufacturer.
The images referring to the textile details may
differ from the collection purchased.
For more information, consult our website:
www.pegperego.com
INSTRUCTIONS
1 OPENING: Before opening the frame, if present, remove
(without using blades) all die-cut cardboard.
WARNING:
_ DO NOT PULL OR FORCE THE FASTENER BEYOND ITS LIMIT.
_ DO NOT USE THE FASTENER AS A HANDLE BAR FOR
TRANSPORT OR TO CARRY WEIGHTS.
DO NOT HANG BAGS OR OTHER ACCESSORIES ON THIS
ELEMENT.
Press the side fastener downwards, grip the upper ends
of the handle bar and rotate them towards you until the
chassis has opened completely (fig_a). Opened chassis
(fig_b). The chassis is opened correctly when you hear a
click, which corresponds to the handle bar frame attaching
- please look at the picture.
2 FITTING THE WHEELS: slot the rear wheel crosspiece onto
the uprights (fig_a), ensuring that it is facing the right
way, then attach the rear wheels until they click into place
(fig_b) . To assemble the front wheels, fit them into the
slots until they lock into place (fig_c).
3 FITTING THE HANDLE BAR: insert the handlebar into the
frame (fig_a) as shown in the picture. For the attachment
to be complete, press the two buttons on the side of the
handle bar (fig_b) and press the handle bar until you hear it
click (fig_c).
4 BASKET ASSEMBLY: to facilitate basket assembly, pull the
tab outwards and lift as shown in the figure (fig_a).
Slip the basket flap into the slot along the front bar of the
chassis (Fig_b).
5 Fasten the basket eyelets to the buttons on each side of
the frame.
6 To complete the basket attachment procedure for the front
part, you are required to insert the supplied tie (fig_1) as
follows:
position it between the basket and buttons, as shown (fig_2)
and use your finger to push downwards, so as to complete
the attachment procedure (fig_3).
Repeat the same procedure for the other side of the basket.
7 Attaching the rear part of the basket.
Remove the card from the rear bar.
Fasten the upper basket eyelet to the button on each side of
the frame (Fig_a).
Fasten the basket's two lower eyelets to the two buttons on
the rear bar of the frame (Fig_b).
8 Basket fastened correctly (fig_g).
Lastly, re-position the footrest, pressing inward with your
hand as shown in the figure (fig_h).
It is possible to increase the basket capacity by pulling the
tab outwards (fig_i).
WARNING! If you do not hook the basket on correctly, as
shown, the basket will be unable to support the weight of
loads placed in it.
9 FIXED OR SWIVELLING FRONT WHEELS: to lock the front
wheels, rotate the lever anticlockwise onto the locked
padlock (fig_a), to release the wheels - turn the lever
clockwise to the unlocked padlock (fig_b). On difficult
terrain, we recommend using fixed wheels.
10 BRAKE: press the lever down to apply the brake and lock
the frame. Do the opposite to release the brake.
11 ADJUSTABLE HANDLE BAR: to adjust the height of the
handlebar, pull the levers towards you (fig_a) and move
the handle bar until it clicks (fig_b). The handle bar can
be adjusted in several positions.
12 FOLDING: lock the front wheels into fixed position
(fig_a), put the handle bar to its lowest position (fig b).
Rotate the safety lever to the left (fig_c) and pull the
frame's internal handle towards you (fig_d). Lift the handle
until the frame is completely folded (fig_e).
13 To fold correctly, make sure the side hook is engaged
- 12 -