Control Panel; Button Function - Franke FSW 918 BK/XS Bedienungsanleitung Und Einrichtung

USE
A
- When power is supplied to the hood, LED A flashes for approximately 10 seconds; during this time the interface is not enabled.
- When the control panel functions are not active only button A can be seen. When this is pressed all the other commands become visible.
- The functions selected are shown by backlighting the button at maximum intensity, while the other buttons are lit at reduced intensity.
- If all the functions are off the panel will switch off after 30 seconds, or when button A is pressed.
Button Function
A Press briefly to turn the motor Off.
Press and hold the button for approximately 4 seconds, with all the loads
turned off (Motor and Lights) and no alarms triggered, to turn the Remote
control on/off.
The procedure can be activated with the door in any position.
B Press briefly to activate speed one.
Press and hold for 2 seconds to activate the 24H function in which the motor
turns on at a speed that allows suction for 10 minutes every hour; at the end
of the 24h the function is deactivated.
To deactivate it, press and hold button B again for 2 seconds, or press button
A or button H.
C Activates speed two.
D Activates speed three.
E Press briefly to activate speed four.
Press and hold for 2 seconds to activate Intensive speed. This speed is timed
to run for 10 minutes. At the end of this time the system will automatically
return to the speed set before.
Cannot be activated if the Delay or 24H functions are active.
It is disabled by pressing any of the Speed buttons or turning the Motor off.
F Press briefly to turn the DELAY on/off, this enables automatic shutdown of
the Motor and the Lighting with a 30' delay.
Can be activated with the motor on (unless intensive or 24H is running).
Press and hold the button for approximately 4 seconds, with all the loads
turned off (Motor and Lights), to turn the Activated Charcoal Filter alarm
on.
To turn it off, press and hold the button again for 4 seconds.
With the filter alarm triggered, press the button briefly to Reset the alarm.
These signals are only visible with the motor turned off and the control panel
active.
The Reset is signalled by the fact that LED F turns off.
G Press briefly to turn the Secondary Lights (spotlights) on and off at maxi-
mum intensity.
The button is also active with the door closed.
Press and hold the button for 2 seconds to turn the Courtesy Lights On
H Door Closed:
- Press and hold for approximately 2 Seconds to open the door, turn the
motor on at the last speed set and turn the Main lights (LEDs) on.
Door Open:
- Press briefly to turn the Main lights (LEDs) On or Off.
- Press for 2 seconds to turn everything off (Motor and Main lights) and
close the door.
EN

Control panel

B
C D
E G
F
Display
The LED on button A is on fixed (when the
motor is on)
The LEDs on buttons A and B flash twice
to indicate that the remote control is on;
The LEDs on buttons A and B flash once to
indicate that the remote control is off;
LED on button B is on fixed
LED on button B flashes (every 0.5 sec-
onds during the 10 minutes on and every 2
seconds during the 50 minutes off)
LEDs on buttons C and A are on fixed
LEDs on buttons D and A are on fixed
LEDs on buttons E and A are on fixed
LED on button E on (flashes every second)
and LED on button A on fixed
LED on button F on fixed if the function is
activated
The LEDS on buttons F and B flash twice
The LEDS on buttons F and B flash once
After 100 hours operation the Led on but-
ton F lights up continuously to indicate
saturation of the Metal Grease Filters.
After 200 hours in operation the Led on
button F flashes to indicate saturation of the
Activated Charcoal filters.
LED on button G is on fixed
LED on button G is on fixed
LED on button H is on fixed when the
main lights are turned on.
H
2 20