Storage - Scheppach LB5200BP Originalanleitung

Cleaning
• Keep the ventilation slots of the machine clean to
prevent overheating of the engine.
• Regularly clean the machine housing with a soft cloth,
preferably after each use.
• Keep the ventilation slots free from dust and dirt.
• If the dirt does not come off use a soft cloth moistened
with soapy water.
• Regularly check the device before starting work.
• Never use water to clean or spray the device. Clean
the motor casing with a damp cloth and never use de-
tergents or solvents! This may damage the device's
plastic parts. Dry the motor casing carefully afterwards.
• Only use OEM parts for maintenance work. Using parts
other than original parts can cause damage to the ma-
chine.
Maintenance
Our machines have been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
machine care and regular cleaning.
Keep all nuts, bolts and screws tight to be sure the
appliance is in safe working
condition.
• Replace worn or damaged parts.
• Use only genuine replacement parts and accessories
• Store the appliance only in a dry place.
The user is responsible for all damages caused by non-
compliance with instructions in this manual. This also
applies to non-authorized modifications of the tool, use of
non-authorized spare parts, accessories, working tools,
unrelated and not intended use, secondary damages
due to use of faulty components.
Warning!
Use only original manufacturer's replacement parts,
accessories and attachments. Failure to do so can
cause poor performance, possible injury and may void
your warranty.
Important hint in case of sending the equipment to
a service station:
Due to security reasons please see to it that the equip-
ment is sent back free of oil and gas!
Ordering replacement parts
Please quote the following data when ordering repla-
cement parts:
• Type of machine
• Article number of the machine
GB:
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the
following parts are therefore also required for use as
consumables.
24 GB
Wear parts*
• Spark plug
• Air filter
• Fuel filter
* Not necessarily included in the scope of delivery!

10. Storage

Cleaning
Keep handles free of oil, so you always have a secure
hold.
Clean the equipment as required with a damp cloth and,
if necessary, mild washing up liquid.
Important!
Always pull out the spark boot plug each time before
carrying out any cleaning.
Never immerse the equipment in water or other liquids
in order to clean it.
Store the petrol multi garden tool in a safe and dry place
out of the reach of children.
Storage
Important: Never put the equipment into storage for lon-
ger than 30 days without carrying out the following steps.
Storing the equipment
If you intend to store the equipment for longer than 30
days, the equipment must be prepared accordingly.
Otherwise the fuel still remaining in the carburetor will
evaporate and leave a rubbery sediment. This can cause
problems when starting up the equipment and may re-
quire expensive repairs.
Slowly remove the fuel tank cap to release any pressure
that may have formed in the tank. Carefully empty the
tank.
To remove the fuel from the carburetor, start the engine
and let it run until the equipment stops.
Leave the engine to cool (approx. 5 minutes).
Remove the spark plug (see section Change and clean
the spark plug).
Add one teaspoon of 2-stroke engine oil into the combus-
tion chamber. Slowly pull the starter cord several times
to apply a layer of oil to all internal components. Fit the
spark plug again.
Note: Store the equipment in a dry place and far away
from possible ignition sources such as an oven, a gas-fi
red hot water boiler, a gas-fi red dryer, etc.
Putting the equipment back into operation
Remove the spark plug (see section Change and clean
the spark plug).
Quickly tug on the starter cord to remove excess oil from
the combustion chamber.
Clean the spark plug and check that the electrode gap
is correct, or insert a new spark plug with the correct
electrode gap.
Prepare the equipment for operation.