Specifications; Operation - Monacor SA-200 Bedienungsanleitung

230V~
50 Hz
FUSE
USE ONLY WITH A 250V FUSE
5 6
4.1 Rack installation
For installation into a rack, fasten the two mount-
ing brackets supplied with the amplifier to the
left and right sides of the housing . In the rack,
the amplifier requires a height of 1 RS (rack space
= 44 .45 mm) .
The hot air given off by the amplifier must
be dissipated from the rack; otherwise, heat will
accumulate in the rack which may not only damage
the amplifier but also other units in the rack . In case
of insufficient heat dissipation, install a ventilation
unit into the rack .
5 Connection
Always switch off the amplifier before making or
changing any connections .
1) Connect the audio unit (e . g . CD/ MP3 player,
mixer, radio) to the RCA jacks INPUT (7): Connect
the left channel to the white jack and the right
channel to the red jack .
2) Connect the speaker systems to the terminals
SPEAKER (8) (RIGHT = right channel, LEFT = left
channel) . The impedance of the speakers must
not fall below 4 Ω; otherwise, the amplifier may
be damaged . To prevent reverse polarity of the
speaker, always connect the marked core of the
speaker cable to the red terminal .
3) For power supply, connect the mains jack (5) to
a socket (230 V~ / 50 Hz) using the mains cable
provided .

6 Operation

1) Before switching on the amplifier for the first
time, set the volume controls LEFT and RIGHT (2)
to "0" .
2) Switch on the audio unit connected .
3) Switch on the amplifier with the POWER
switch (4); the power LED ON (3) lights up .
4) Use the controls LEFT and RIGHT to adjust the
desired volume and at the same time the stereo
All rights reserved by MONACOR
reproduced in any form or by any means for any commercial use.
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may be
®
INPUT SPEAKER 4-8 Ω
RIGHT
L
R
7
balance, if necessary . The red LED CLIP (1) is an
overload indication; in case of overload of an
amplifier channel, the LED of this channel will
light up . In this case, turn back the correspond-
ing volume control accordingly .
CAUTION Never adjust a very high volume .
Permanent high volumes may
damage your hearing! Your ear
will get accustomed to high vol-
umes which do not seem to be that high after
some time . Therefore, do not further increase
a high volume after getting used to it .
5) After operation, switch off the amplifier with
the POWER switch . To prevent switching noise,
always switch off the amplifier before switching
off the other units of the audio system .

7 Specifications

RMS output power
at 4 Ω: � � � � � � � � � � � � � � � � � 2 × 50 W
at 8 Ω: � � � � � � � � � � � � � � � � � 2 × 30 W
Max� output power: � � � � � � � � � 2 × 100 W
Frequency range: � � � � � � � � � � � 20 – 20 000 Hz
S / N ratio: � � � � � � � � � � � � � � � � 83 dB
Signal input
Sensitivity: � � � � � � � � � � � � � � 420 mV
Impedance:� � � � � � � � � � � � � � 6 kΩ
Connection: � � � � � � � � � � � � � RCA jacks
Power supply: � � � � � � � � � � � � � 230 V~ / 50 Hz
Power consumption: � � � � � � � � 210 VA max�
Ambient temperature: � � � � � � � 0 – 40 °C
Dimensions (W × H × D): � � � � 431 × 55 × 255 mm
Weight: � � � � � � � � � � � � � � � � � � 4�6 kg
Subject to technical modification .
LEFT
8
7