Makita BUR181 Bedienungsanleitung Seite 11

Nylon cutting head
NOTICE:
The bump feed will not operate properly if the
•
Nylon cutting head is not rotating.
Fig.6
The nylon cutting head is a single string trimmer head
provided with a bump & feed mechanism.
To cause the nylon cord to feed out, the cutting head
should be bumped against the ground while the tool is
running. As the nylon cord is feeding out it will
automatically be cut to the proper length by the cutter
on the guard.
NOTE:
If the nylon cord does not feed out while bumping
•
the head, rewind/replace the nylon cord by
following the
"Installing or removing the Nylon cutting head" and
"Winding a new Nylon cord on the spool."
Do not bump the tool to the concrete or asphalt
•
surface. Bumping to this kind of objects may
cause the tool damage.
ASSEMBLY
WARNING:
Always be sure that the tool is switched off
•
and battery cartridge is removed before
carrying out any work on the tool. Failure to
switch off and remove the battery cartridge may
result in serious personal injury from accidental
start-up.
Never start the tool unless it is completely
•
assembled. Operation of the tool in a partially
assembled state may result in serious personal
injury from accidental start-up.
Installing the front grip
Fig.7
Put the front grip on the front grip holder and secure it
with a hex bolt and the clamping nut provided with the
string trimmer as shown in the figure. At this time, the
hex bolt needs to be installed from the side in which the
hex bolt lock port is located and the clamping nut needs
to be installed from the opposite side.
NOTE:
The front grip has a edge-to-edge cut slit in its
•
mounting area. Using this slit allows you to easily
install the front grip on the front grip holder.
The front grip angle is adjustable. To adjust the front
grip angle, loosen the claming nut, set the front grip at
an proper angle according to your work and then tighten
the nut clockwise firmly.
procedures described
Installing the guard
CAUTION:
While installing the guard, be careful not to
•
contact the nylon cord cutter provided on the
guard. Contact with the cutter could result in
personal injury.
Fig.8
Mount the guard by fitting it on to the motor housing so
that the Nylon cord is not pinched between the guard
and the motor housing, and then secure it with two
screws. Before starting the trimmer, take away the
cutter cover from the cord cutter.
Installing or removing the Nylon cutting head
WARNING:
under
Before installing or removing the Nylon cutting
•
head (both spool cover and spool, and
hereafter called this way), make sure that the
tool is switched off and the battery cartridge is
removed from the tool. Failure to switch off the
tool and remove the battery cartridge may cause a
personal injury.
CAUTION:
While installing or removing the Nylon cutting
•
head, be careful not to contact the nylon cord
cutter provided on the guard. Contact with the
cutter could result in personal injury.
Fig.9
Fig.10
To remove the Nylon cutting head (spool and spool
cover) from the string trimmer, press in the latches
forcefully on both sides of the spool cover and raise it.
Fig.11
NOTICE:
Make sure that the spring is installed inside the
•
spool holder.
To install a cord-newly-wound Nylon cutting head (spool
and spool cover) on the string trimmer, align the Nylon
cord eyehole with the notch of the Nylon cutting head
installation port on the trimmer and then press in it until
a click is heard.
Winding a new Nylon cord on the spool
Fig.12
Remove the spool from the spool cover and take off the
remaining used Nylon cord from the spool.
Fig.13
Insert a Nylon cord to the retainer shown in the figure.
Fig.14
Wind it tightly flat around the spool in the direction of
arrow on the spool so that the wound Nylon cord
surface appears uniform over the winding area.
11