Timbertech RadianceRail Handbuch Für Wartung Und Installation Seite 38

Installing Post Mounted Accent Light
Accent Light wire channel must be routed during the installation of
1
the Post Cover. The Post Cover and the wood post must be prepared
in advance to accommodate installation of the Accent Light. (No
Installation von Bohlenleuchten
Installing In-Deck Light
post preparation is necessary for RadianceRail.)
If using Ornamental Rail or BuilderRail, prepare the wood post
In-deck light should be installed in a low foot-traffic area. Bohlenleuchten sollten in Bereichen mit geringer Begehungsaktivität installiert werden.
by routing a 1/2" wide by 1/4" deep wire channel up the center
In-deck light can only be used when there is room under the deck to access the wires to make all of the connections
Bohlenleuchten können nur verwendet werden, wenn unter der Terrasse genug Platz vorhanden ist, so dass alle Kabel zur Verkabelung
of the post on the face where the Accent Light will be mounted.
zugänglich sind.
For main cable, route the center of post or slightly bevel the
corner of the 4x4 post.
Locate and mark the centerline of the deck plank where the
1 1 Lokalisieren und markieren Sie die Mittellinie der Terrassenbohle,
in-deck light will be mounted.
in der die Bohlenleuchte montiert werden soll.
2 Prepare the Post Cover in the following manner:
• Cut the Post Cover to the desired length.
• Determine the height the Accent Light will be mounted.
On the desired point of the center line, use a 1" spade bit to
2 2
Verwenden Sie einen 25 mm (1")-Flachfräsbohrer zur
create a through hole (be sure not to drill into the substructure.)
Herstellung der Durchbohrung. (Achten Sie darauf, nicht den
• Mark the location of the wire hole and the mounting
Unterbau anzubohren.)
screw holes using the template provided on the
instructions that come with the product.
• Drill a 3/8" hole for the wire and drill two 7/64" holes
for the mounting screws.
If a Post Skirt is used, install it over the wood post before
3
installing the Post Cover. You will not be able to install Post
Skirt after Post Cover and Accent Light are in place.
3
Führen Sie das Kabel der Leuchte in die Durchbohrung ein.
3
Guide the light's wire into the through hole.
4 Remove Accent Light Cover from Accent Light Back Plate by
loosening Set Screw located at bottom of Accent Light Cover.
Route the Accent Light wire through the wire hole in the Post
5
Cover then invert the Post Cover and allow the wire to extend out
the top end of the Post Cover.
6 Hold the Accent Light Back Plate loosely in position and slide the
Post Cover over the wood post and into the Post Skirt. Make sure
Drücken Sie die Leuchte in die Durchbohrung ein, bis der Flansch
4
Push the lighting fixture into the through hole until the flange
4
the wire is in the routed wire channel.
die Terrassenoberfl äche berührt.
touches the deck surface.
7
Attach the Accent Light Back Plate to the post using two #8 x
3/4" screws provided.
Die Kabelanschlüsse können dann unter der Terrassenoberfl äche
5
The wire connections can then be made under the deck's
5
vorgenommen werden.
surface.
8
Install Lamp. Do not touch the Lamp with bare hands, oil from
skin may damage Lamp. Use a soft cloth when handling Lamp.
Re-install Accent Light Cover and secure with Set Screw with
Allen Wrench.
9
Trim excess wire and make wiring connections.
(See Connections section of manual).
37
Routed Channel for
Accent Light Wire
Drill Template
Accent Light
Back Plate
#8 x 3/4"
Screws
Accent Light
Cover
Lamp
Set
Screw
Routed Channel for
Main Cable
Post Skirt
D ri
3 /8 ll
" H
o le
D ri
9 /6 ll
4 "
H o le
s
P o s
t M
A c c o u n
e n t
te d
T e m L ig
p la h t
te
U P