auna multimedia TT-18SB Bedienungsanleitung Seite 14

PHONO & ENCODING
NOTED:
- REMOVE THE STYLUS PROTECTOR.
- - BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM
REST BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS. REST BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.
1. PRESS FUNCTION BUTTON (4) TO SELECT "PHON" ON DISPLAY.
2. SET THE SPEED SELECTOR (26) TO THE PROPER POSITION DEPENDING ON THE RECORD TO BE
PLAYED.
3. PLACE THE RECORD ON THE PLATTER (28), USE THE 45 RPM ADAPTOR IF REQUIRED. 3. PLACE THE RECORD ON THE PLATTER (28), USE THE 45 RPM ADAPTOR IF REQUIRED.
4. PUSH THE LIFT LEVER (24) UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK, AND THEN
SLOWLY MOVE IT TO THE RECORD SIDE. THE PLATTER WILL START TO ROTATE.
5. PUT DOWN THE LIFT LEVER (24) TO DROP THE TONE ARM AND TOUCH THE RECORD GENTLY.
PHONO PLAYING STARTS NOW.
6. PUSH THE LIFT LEVER (24) UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK, NOW
PLATTER WILL STILL BE ROTATING BUT PHONO PLAYING WILL STOP. TO CONTINUE THE
PLAYING, THE USER NEEDS TO PUT DOWN THE LIFT LEVER (24).
7. ADJUST THE VOLUME TO THE DESIRED LEVEL.
8. AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING. PUSH THE LIFT
LEVER (24) UPWARD TO RAISE THE TONE ARM AND MOVE IT TO THE ARM PARK, AND THEN PUT
DOWN THE LIFT LEVER (24).
9. TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE ARM PARK.
REMARK:
AS SOME KIND OF RECORD THE AUTO-STOP AREA WAS OUT OF THE UNIT SETTING, SO IT WILL
STOP BEFORE THE LAST TRACK FINISHES. IN THIS CASE, SELECT THE AUTO-STOP SWITCH (25)
TO " OFF " POSITION, THEN IT WILL RUN TO THE END OF THE RECORD BUT WILL NOT STOP
AUTOMATICALLY (TURN OFF THE UNIT BY POWER BUTTON OR SWITCH BACK THE AUTO-STOP SWITCH (25)
TO " ON " POSITION TO STOP THE PLATTER ROTATE). THEN PUT BACK THE TONE ARM TO THE ARM PARK.
PHONO ENCODING
1. PRESS FUNCTION BUTTON (4) TO SELECT "PHON" ON DISPLAY AND THEN INSERT MEMORY
DEVICE (USB DRIVE, SD OR MMC CARD).
2. PRESS THE "REC" BUTTON (2), IT WILL TAKE 3-5 SECONDS TO READ MEMORY DEVICE. THEN
USB OR SD ICON WILL BE FLASHING.
3. PRESS SKIP
(USB OR SD) FOR ENCODING. THEN PRESS THE "REC" BUTTON (2) AGAIN TO CONFIRM. AND
THE SYSTEM IS STARTING THE ENCODING MODE AFTER FEW SECONDSS.
4. IF ONLY USB DRIVE OR SD/MMC CARD IS INSERTED, STEP 3 CAN BE SKIPPED.
5. THE REC ICON WILL BE FLASHING ON THE DISPLAY DURNIG ENCODING.
6. TO FINISH ENCODING:
- PRESS STOP
WILL STOP OPERATION. PRESS REC BUTTON AGAIN, ENCODING AND TURNTABLE WILL RESUME
TO WORK.
- PRESS AND HOLD REC BUTTON CONTINUOUSLY, "REC" WILL DISAPPEAR, RECORDING WILL
STOP OPERATION, BUT TURNTABLE WILL KEEP OPERATION. PRESS REC BUTTON AGAIN,
ENCODING WILL RESUME TO WORK.
UP BUTTON (15) OR SKIP DOWN
BUTTON OR REC BUTTON, "REC" WILL DISAPPEAR, RECORDING AND TURNTABLE
BUTTON (14) TO SELECT DESIRED MODE
14